The restoration of class II cavities is predominantly carried out with composite materials. Due to the high failure rate in restoring this type of cavity, composite materials with much-improved properties and new application techniques have been promoted. The study aimed to analyze the mechanical behavior of several topical composite materials (nanocomposites, nanohybrids and ormocer) using different application techniques. In a lower second molar, a class II occlusal cavity was prepared. As filling materials, we used the following combinations: Admira Fusion and Admira Fusion Flow, Grandio and Grandio Flow, Filtek Supreme XT and Filtek Supreme Flow. These were applied using a snow plow, injection molded and Bichacho techniques. Three-dimensional scanning of the molar with the prepared cavity was performed, and then scanning of each layer of added composite material was performed, obtaining three-dimensional models. The virtual molar models were analyzed with software specific to the finite element analysis method, where their physical-mechanical properties were entered and assigned to the components of the virtual molar. Simulations at high forces specific to bruxism were then carried out and analyzed, and compared. The values of displacements and strain, for all six analyzed situations, are relatively small (range from 5.25 × 10−6–3.21 × 10−5 for displacement, 6.22 × 10−3–4.34 × 10−3 for strain), which validates all three methods and the materials used. As far as the stress values are concerned, they are similar for all methods (250–300 MPa), except for the snow plow and injection-molded techniques using Grandio and Grandio Flow composites, where the maximum von Mises stress value was more than double (approximately 700 MPa). When using the combination of Grandio and Grandio Flow materials, the 1 mm thickness of the fluid composite layer was found to have a major influence on occlusal forces damping as opposed to 0.5 mm. Therefore, the Bichacho technique is indicated at the expense of the snow plow and injection-molded techniques. The composite materials used by us in this study are state-of-the-art, with clear indications for restoring cavities resulting from the treatment of carious lesions. However, their association and application technique in the case of Class II cavities is of clinical importance for resistance to masticatory forces.

The purpose of this study was to show the improved outcomes of restoring endodontically treated teeth with fiberglass posts compared to restorations using metal posts. In our study, we used the Finite Element Method (FEM), which is based on the principle that a physical model that supports a given load distributes the stress throughout its volume. We sought to assess what stress results in a tooth when it is restored using a fiberglass post compared to restoration using a metal post. The finite element analysis showed that a system consisting of a tooth with a fiberglass post is more stable in terms of the maximum stress than a system consisting of a tooth with a metal post. The maximum displacements and deformations were obtained in the case of a canine restored with a fiberglass post, which showed that this system had a high elasticity, therefore, higher strength than a canine restored with a metal post, which had high rigidity.

We aim to review data on 3beta-hydroxysteroid dehydrogenase type II (3βHSD2) deficiency. We identified 30 studies within the last decade on PubMed: 1 longitudinal study (N = 14), 2 cross-sectional studies, 1 retrospective study (N = 16), and 26 case reports (total: 98 individuals). Regarding geographic area: Algeria (N = 14), Turkey (N = 31), China (2 case reports), Morocco (2 sisters), Anatolia (6 cases), and Italy (N = 1). Patients’ age varied from first days of life to puberty; the oldest was of 34 y. Majority forms displayed were salt-wasting (SW); some associated disorders of sexual development (DSD) were attendant also—mostly 46,XY males and mild virilisation in some 46,XX females. SW pushed forward an early diagnosis due to severity of SW crisis. The clinical spectrum goes to: premature puberty (80%); 9 with testicular adrenal rest tumours (TARTs); one female with ovarian adrenal rest tumours (OARTs), and some cases with adrenal hyperplasia; cardio-metabolic complications, including iatrogenic Cushing’ syndrome. More incidental (unusual) associations include: 1 subject with Barter syndrome, 1 Addison’s disease, 2 subjects of Klinefelter syndrome (47,XXY/46,XX, respective 47,XXY). Neonatal screening for 21OHD was the scenario of detection in some cases; 17OHP might be elevated due to peripheral production (pitfall for misdiagnosis of 21OHD). An ACTH stimulation test was used in 2 studies. Liquid chromatography tandem–mass spectrometry unequivocally sustains the diagnostic by expressing high baseline 17OH-pregnenolone to cortisol ratio as well as 11-oxyandrogen levels. HSD3B2 gene sequencing was provided in 26 articles; around 20 mutations were described as “novel pathogenic mutation” (frameshift, missense or nonsense); many subjects had a consanguineous background. The current COVID-19 pandemic showed that CAH-associated chronic adrenal insufficiency is at higher risk. Non-adherence to hormonal replacement contributed to TARTs growth, thus making them surgery candidates. To our knowledge, this is the largest study on published cases strictly concerning 3βHSD2 deficiency according to our methodology. Adequate case management underlines the recent shift from evidence-based medicine to individualized (patient-oriented) medicine, this approach being particularly applicable in this exceptional and challenging disorder.