No abstract

Article type: Full paperOrganic gelators as growth control agents for stable and reproducible hybrid perovskite-based solar cells Sofia Masi, [a] Aurora Rizzo, [a] Rahim Munir, [b] Andrea Listorti, [a,c] Antonella Giuri, [d] Carola Esposito Corcione, [d] Neil D. Treat, [e] Giuseppe Gigli, [a,c] Aram Amassian, [b] * Natalie Stingelin, [e,f] * and Silvia Colella* [a,c] Low molecular-weight organic gelators are widely used to influence the solidification of polymers, with applications ranging from packaging items, food containers to organic electronic devices, including organic photovoltaics. Here, this concept is extended to hybrid halide perovskite-based materials. In-situ time-resolved grazing incidence wide angle x-ray scattering (GIWAXS) measurements performed during spin-coating reveal that organic gelators beneficially influence the nucleation and growth of the perovskite precursor phase. This can be exploited for the fabrication of planar n-i-p heterojunction devices with MAPbI3 (MA = CH3NH3 + ) that display a performance that not only is enhanced by ∼25% compared to solar cells where the active layer was produced without the use of a gelator but that also feature a higher stability to moisture and a reduced hysteresis. Most importantly, the presented approach is straight-forward and simple, and it provides a general method to render the film-formation of hybrid perovskites more reliable and robust, analogous to the control that is afforded by these additives in the processing of commodity 'plastics'.

The influence of different graphite-based nanofillers on epoxide ring opening reactions, as induced by amines for diglycidyl ether of bisphenol A (DGEBA), is studied. Direct kinetic studies, with full chemical characterization and quantitative evaluation of the low molecular mass products, for reactions of DGEBA with primary and secondary monoamines as well with alcohols, are conducted. Moreover, the kinetic behavior of a commercial epoxy resin based on DGEBA and a diamine, leading to crosslinked insoluble networks, is studied by indirect methods, such as differential scanning calorimetry (DSC) and rheometry. The reported results show a relevant catalytic activity of graphene oxide on epoxy resin crosslinking by amines. For instance, for a graphene oxide content of 3 wt%, the exothermic crosslinking DSC peak is shifted (upon heating at 10 °C min-1) from 113 °C down to 96 °C, while the gel time at 50 °C is reduced by a factor of 2.5. This behavior is due to the ability of graphene oxide to catalyze primary amine-epoxy, secondary amine-epoxy and mainly hydroxyl-epoxy additions

Hybrid organic–inorganic halide perovskites have emerged at the forefront of solution‐processable photovoltaic devices. Being the perovskite precursor mixture a complex equilibrium of species, it is very difficult to predict/control their interactions with different substrates, thus the final film properties and device performances. Here the wettability of CH3NH3PbI3 (MAPbI3) onto poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) hole transporting layer is improved by exploiting the cooperative effect of graphene oxide (GO) and glucose inclusion. The glucose, in addition, triggers the reduction of GO, enhancing the conductivity of the PEDOT:PSS+GO+glucose based nanocomposite. The relevance of this approach toward photovoltaic applications is demonstrated by fabricating a hysteresis‐free MAPbI3 solar cells displaying a ≈37% improvement in power conversion efficiency if compared to a device grown onto pristine PEDOT:PSS. Most importantly, VOC reaches values over 1.05 V that are among the highest ever reported for PEDOT:PSS p‐i‐n device architecture, suggesting minimal recombination losses, high hole‐selectivity, and reduced trap density at the PEDOT:PSS along with optimized MAPbI3 coverage.