Yttria-stabilized zirconia (YSZ) is the most common electrolyte material for solid oxide fuel cells. Herein, we conducted a comparative study on the densification behavior of three different kinds of commercial 8 mol% YSZ powders: (i) TZ-8Y (Tosoh, Japan), (ii) MELox 8Y (MEL Chemicals, UK), and (iii) YSZ-HT (Huatsing Power, China). The comparison was made on both the selfsupporting pellets and thin-film electrolytes coated onto a NiO-YSZ anode support. For the pellets, MELox 8Y showed the highest densification at lower sintering temperatures with 93% and 96% of the theoretical density at 1250 and 1300 ℃, respectively. Although YSZ-HT showed a higher sintering rate than TZ-8Y, a sintering temperature of 1350 ℃ was required for both the powders to reach 95% of the theoretical density. For the thin-film electrolytes, on the other hand, YSZ-HT showed the highest sintering rate with a dense microstructure at a co-sintering temperature of 1250 ℃. Our results indicate that besides the average particle size, other factors such as particle size distribution and post-processing play a significant role in determining the sintering rate and densification behavior of the YSZ powders. Additionally, a close match in the sintering shrinkage of the electrolyte and anode support is important for facilitating the densification of the thin-film electrolytes.

Solid oxide fuel cells (SOFCs) are promising electrochemical energy conversion devices owing to their high power generation efficiency and environmentally benign operation. Micro-tubular SOFCs, which have diameters ranging from a few millimeters to the sub-millimeter scale, offer several advantages over competing SOFCs such as high volumetric power density, good endurance against thermal cycling, and flexible sealing between fuel and oxidant streams. Herein, we successfully realized a novel micro-tubular SOFC design based on a porous yttria-stabilized zirconia (YSZ) support using multi-step dip coating and co-sintering methods. The micro-tubular SOFC consisted of Ni-YSZ, YSZ, and strontium-doped lanthanum manganite (LSM)–YSZ as the anode, electrolyte, and cathode, respectively. In addition, to facilitate current collection from the anode and cathode, Ni and LSM were applied as an anode current collector and cathode current collector, respectively. Micro-crystalline cellulose was selected as a pore former to achieve better shrinkage behavior of the YSZ support so that the electrolyte layer could be densified at a co-sintering temperature of 1300°C. The developed micro-tubular design showed a promising electrochemical performance with maximum power densities of 525, 442, and 354 mW cm−2 at 850, 800, and 750°C, respectively.

Freeze casting is an established method for fabricating porous ceramic structures with controlled porosity and pore geometries. Herein, we developed a novel freeze casting and freeze drying process to fabricate tubular anode supports for solid oxide fuel cells (SOFCs). Freeze casting was performed by injecting aqueous anode slurry to a dual‐purpose freeze casting and freeze drying mold wrapped with peripheral coils for flowing a coolant. With the use of an ice barrier layer, proper control of the experimental setup, and adjustments in the drying temperature profile, complete drying of the individual anode tubes was achieved in 4 hours. The freeze‐cast anode tubes contained radially aligned columnar pore channels, thus significantly enhancing the gaseous diffusion. SOFC single cells with conventional Ni/yttria‐stabilized zirconia/strontium‐doped lanthanum manganite materials were prepared by dip coating the thin functional layers onto the anode support. Single cell tests showed that the concentration polarization was low owing to the highly porous anode support with directional pores. With H2/N2 (1:1) fuel, maximum power densities of 0.47, 0.36, and 0.27 W/cm2 were recorded at 800°C, 750°C, and 700°C, respectively. Our results demonstrate the feasibility of using freeze casting to obtain tubular SOFCs with desired microstructures and fast turn‐around times.

No abstract