Calcium phosphate (Ca-P) cements are injectable, self-setting ceramic pastes generally known for their favorable bone response. Ingrowth of bone and subsequent degradation rates can be enhanced by the inclusion of macropores. Initial porosity can be induced by CO(2) foaming during setting of the cement, whereas secondary porosity can develop after hydrolysis of incorporated poly(DL-lactic- co-glycolic acid) (PLGA) microparticles. In this study, we focused on the biological response to porous PLGA/Ca-P cement composites. Pre-set composite discs of four formulations (4 wt% or 15 wt% PLGA microparticles and low or high CO(2) induced porosity) were implanted subcutaneously and in cranial defects in rats for 12 weeks. Histological analysis of the explanted composites revealed that bone and fibrous tissue ingrowth was facilitated by addition of PLGA microparticles (number average diameter of 66 +/- 25 microm). No adverse tissue reaction was observed in any of the composites. Significant increases in composite density due to bone ingrowth in cranial implants were found in all formulations. The results suggest that the PLGA pores are suitable for bone ingrowth and may be sufficient to enable complete tissue ingrowth without initial CO(2) induced porosity. Finally, bone-like mineralization in subcutaneous implants suggests that, under appropriate conditions and architecture, porous PLGA/Ca-P cement composites can exhibit osteoinductive properties. These PLGA/Ca-P composites are a promising scaffolding material for bone regeneration and bone tissue engineering.

The primary driver for valvular calcification is the differentiation of valvular interstitial cells (VICs) into a diseased phenotype. However, the factors leading to the onset of osteoblastic-like VICs (obVICs) and resulting calcification are not fully understood. This study isolates the effect of substrate surface chemistry on in vitro VIC differentiation and calcified tissue formation. Using ω-functionalized alkanethiol self-assembled monolayers (SAMs) on gold [CH3 (hydrophobic), OH (hydrophilic), COOH (COO−, negative at physiological pH), and NH2 (NH3+, positive at physiological pH)], we have demonstrated that surface chemistry modulates VIC phenotype and calcified tissue deposition independent of osteoblastic-inducing media additives. Over seven days VICs exhibited surface-dependent differences in cell proliferation (COO− = NH3+> OH > CH3), morphology, and osteoblastic potential. Both NH3+and CH3-terminated SAMs promoted calcified tissue formation while COO−-terminated SAMs showed no calcification. VICs on NH3+-SAMs exhibited the most osteoblastic phenotypic markers through robust nodule formation, up-regulated osteocalcin and α-smooth muscle actin expression, and adoption of a round/rhomboid morphology indicative of osteoblastic differentiation. With the slowest proliferation, VICs on CH3-SAMs promoted calcified aggregate formation through cell detachment and increased cell death indicative of dystrophic calcification. Furthermore, induction of calcified tissue deposition on NH3+ and CH3-SAMs was distinctly different than that of media induced osteoblastic VICs. These results demonstrate that substrate surface chemistry alters VIC behavior and plays an important role in calcified tissue formation. In addition, we have identified two novel methods of calcified VIC induction in vitro. Further study of these environments may yield new models for in vitro testing of therapeutics for calcified valve stenosis, although additional studies need to be conducted to correlate results to in vivo models.

Many publications have examined the biodegradable polymer poly(propylene fumate) (PPF) for use in tissue engineering applications. We have examined a similar crosslinkable polymer system, poly(propylene fumerate)-co-(propylene maleate) (PPFcPM), derived from maleic anhydride (MA) and 1,2-propylene diol (PD). This copolymer system uses a less expensive monomer as well as leads to varied ratios of fumerate to maleate groups, allowing tuning of the crosslinked polymer properties such as degradation rate. Two different reaction conditions were used to synthesize the copolymer from MA and PD. In the first case (Method A), toluene was used as a solvent to azeotropically (85 C) remove water to drive the acid catalyzed esterification reaction. In the second case (Method B), the initial ring opening reaction was conducted, followed by addition of catalyst and removal of water to produce polymer of higher molecular weight. Both polymer systems had glass transition temperatures (T g ) below room temperature. The low T g PPFcPM was dissolved in chloroform along with the photoinitiator phenylbis(2,4,6-trimethylbenzoyl)-phosphine oxide (BAPO) and electrospun. The polymer fibers were crosslinked soon after they formed to produce noncalendaring 3D porous scaffolds. Control experiments without the BAPO photoinitiator did not produce fiber mats.

Poly(N-isopropyl acrylamide) (pNIPAM) is a "smart" polymer that responds to changes in altering temperature near physiologically relevant temperatures, changing its relative hydrophobicity. Mammalian cells attach to pNIPAM at 37 °C and detach spontaneously as a confluent sheet when the temperature is shifted below the lower critical solution temperature (∼32 °C). A variety of methods have been used to create pNIPAM films, including plasma polymerization, self-assembled monolayers, and electron beam ionization. However, detachment of confluent cell sheets from these pNIPAM films can take well over an hour to achieve potentially impacting cellular behavior. In this work, pNIPAM mats were prepared via electrospinning (i.e., espNIPAM) by a previously described technique that the authors optimized for cell attachment and rapid cell detachment. Several electrospinning parameters were varied (needle gauge, collection time, and molecular weight of the polymer) to determine the optimum parameters. The espNIPAM mats were then characterized using Fourier-transform infrared, x-ray photoelectron spectroscopy, and scanning electron microscopy. The espNIPAM mats showing the most promise were seeded with mammalian cells from standard cell lines (MC3T3-E1) as well as cancerous tumor (EMT6) cells. Once confluent, the temperature of the cells and mats was changed to ∼25 °C, resulting in the extremely rapid swelling of the mats. The authors find that espNIPAM mats fabricated using small, dense fibers made of high molecular weight pNIPAM are extremely well-suited as a rapid release method for cell sheet harvesting.

Understanding cellular interactions with material surfaces at the micro-and nanometer scale is essential for the development of the next generation of biomaterials. Several techniques have been used to create micro-and nanopatterned surfaces as a means of studying cellular interactions with a surface. Herein, we report the novel use of interference lithography to create a large (4 cm 2 ) array of 33 nm deep channels in a gold surface, to expose an antireflective coating on a silicon wafer at the bottom of the gold channels. The fabricated pores had a diameter of 140-350 nm separated by an average pitch of 304-750 nm, depending on the fabrication conditions. The gold surface was treated with 2-(2-(2-(11-mercaptoundecyloxy)ethoxy)ethoxy)ethanol to create protein-resistant areas. Fibronectin was selectively adsorbed onto the exposed antireflective coating creating nanometer-scale cell adhesive domains. A murine osteoblast cell line (MC3T3-E1) was seeded onto the surfaces and was shown to attach to the fibronectin domains and spread across the material surface.