Alginate hydrogels are biocompatible, biodegradable, low-cost, and widely used as bioinks, cell encapsulates, three-dimensional culture matrices, drug delivery systems, and scaffolds for tissue engineering. Nevertheless, their limited stiffness hinders their use for certain biomedical applications. Many research groups have tried to address this problem by reinforcing alginate hydrogels with graphene, carbon nanotubes, or silver nanoparticles. However, these materials present nanotoxicity issues, limiting their use for biomedical applications. Other studies show that electrospinning or wet spinning can be used to fabricate biocompatible, micro- and nanofibers to reinforce hydrogels. As a relatively simple and cheap alternative, in this study we used bioengineered bacteria to fabricate amyloid curli fibers to enhance the stiffness of alginate hydrogels. We have fabricated for the first time bioengineered amyloid curli fibers–hydrogel composites and characterized them by a combination of (i) atomic force microscopy (AFM) to measure the Young’s modulus of the bioengineered amyloid curli fibers and study their topography, (ii) nanoindentation to measure the Young’s modulus of the amyloid curli fibers–alginate nanocomposite hydrogels, and (iii) Fourier-transform infrared spectroscopy (FTIR) to analyze their composition. The fabricated nanocomposites resulted in a highly improved Young’s modulus (up to 4-fold) and showed very similar physical and chemical properties, opening the window for their use in applications where the properties alginate hydrogels are convenient but do not match the stiffness needed.

“Cuttlebone,” the internalized shell found in all members of the cephalopod family Sepiidae, is a sophisticated buoyancy device combining high porosity with considerable strength. Using a complementary suite of characterization tools, we identified significant structural, chemical, and mechanical variations across the different structural units of the cuttlebone: the dorsal shield consists of two stiff and hard layers with prismatic mineral organization which encapsulate a more ductile and compliant layer with a lamellar structure, enriched with organic matter. A similar organization is found in the chambers, which are separated by septa, and supported by meandering plates (“pillars”). Like the dorsal shield, septa contain two layers with lamellar and prismatic organization, respectively, which differ significantly in their mechanical properties: layers with prismatic organization are a factor of three stiffer and up to a factor of ten harder than those with lamellar organization. The combination of stiff and hard, and compliant and ductile components may serve to reduce the risk of catastrophic failure, and reflect the role of organic matter for the growth process of the cuttlebone. Mechanically “weaker” units may function as sacrificial structures, ensuring a stepwise failure of the individual chambers in cases of overloading, allowing the animals to retain near-neutral buoyancy even with partially damaged cuttlebones. Our findings have implications for our understanding of the structure-property-function relationship of cuttlebone, and may help to identify novel bioinspired design strategies for light-weight yet high-strength foams.

Successful nanobiotechnology implementation largely depends on control over the interfaces between inorganic materials and biological molecules. Controlling the orientations of biomolecules and their spatial arrangements on the surface may transform many technologies including sensors, to energy. Here, we demonstrate the self-organization of L-lactate dehydrogenase (LDH), which exhibits enhanced enzymatic activity and stability on a variety of gold surfaces ranging from nanoparticles to electrodes, by incorporating a gold-binding peptide tag (AuBP2) as the fusion partner for Bacillus stearothermophilus LDH (bsLDH). Binding kinetics and enzymatic assays verified orientation control of the enzyme on the gold surface through the genetically incorporated peptide tag. Finally, redox catalysis efficiency of the immobilized enzyme was detected using cyclic voltammetry analysis in enzyme-based biosensors for lactate detection as well as in biofuel cell energy systems as the anodic counterpart. Our results demonstrate that the LDH enzyme can be self-immobilized onto different gold substrates using the short peptide tag under a biologically friendly environment. Depending on the desired inorganic surface, the proposed peptide-mediated path could be extended to any surface to achieve single-step oriented enzyme immobilization for a wide range of applications.

There is an emerging interest in developing bio-functionalisation routes serving as platforms for assembling diverse enzymes onto material surfaces. Specifically, the fabrication of next-generation, laboratory-on-a-chip-based sensing and energy-harvesting systems requires controlled orientation and organisation of the proteins at the inorganic interfaces. Herein, the authors take the initial steps towards designing multifunctional, enzyme-based platforms by genetically integrating the engineered materialselective peptide tags for tethering redox enzymes onto electrode surfaces. The authors engineered a fusion protein that genetically conjugates gold-binding peptide to formate dehydrogenase derived from Candida methylica. The expressed proteins were tested for both enzyme activity and self-directed gold-surface functionalisation ability. Their findings demonstrate the successful self-immobilisation of the engineered enzyme onto different gold electrodes while retaining the catalytic activity.Building on the functionalisation by the peptides, a fusion enzyme-integrated circuit-based biosensor system was designed. The catalytic conversion of the formate by the engineered dehydrogenase was successfully monitored on the electrode surface at subsequent intervals. The engineered peptide-mediated self-integrated electrode systems can be extended to develop a wide range of biosensing and energy-harvesting platforms using different combinations of materials and biomolecules. This paper contains supporting information that will be made available online once the issue is published. In the meantime, if you wish to get a copy of the supplementary file, please contact the Journals Editor, Sarah Brown, at sarah.brown@icepublishing.com.

Abstract'Cuttlebone', the internalized shell found in all members of the cephalopod family Sepiidae, is a sophisticated buoyancy device combining high porosity with considerable strength. Using a complementary suite of characterization tools, we identified significant structural, chemical and mechanical variations across the different structural units of the cuttlebone: the dorsal shield consists of two stiff and hard layers with prismatic mineral organization which encapsulate a more ductile and compliant layer with a lamellar structure, enriched with organic matter. A similar organization is found in the lamellar matrix, which consists of individual chambers separated by septa, and supported by meandering plates ('pillars'). Like the dorsal shield, septa contain two layers with lamellar and prismatic organization, respectively, which differ significantly in their mechanical properties: layers with prismatic organization are a factor of three stiffer, and up to a factor of ten harder than those with lamellar organization. The combination of stiff and hard, and compliant and ductile components may serve to reduce the risk of catastrophic failure, and reflect the role of organic matter for the growth process of the cuttlebone. Mechanically 'weaker' units may function as sacrificial structures, ensuring a step-wise failure of the individual chambers in cases of overloading, allowing the animals to retain near-neutral buoyancy even with partially damaged cuttlebones. Our findings have implications for the structure-property-function relationship of cuttlebone, and may help to identify novel bioinspired design strategies for light-weight yet high-strength foams.