In order to produce nanostructured Ti0.9Cr0.1C powders, an elemental powder mixture of titanium, chromium, and graphite is milled in this work using a high-energy ball mill for various milling times. Microstructural characteristics such as crystallite size, microstrain, lattice parameter, and dislocation density are determined using X-ray diffraction (XRD). Mechanical alloying successfully produced nanocrystalline (Ti,Cr)C with an average crystallite size of 11 nm. This size of the crystallites is also directly verified using transmission electron microscopy (TEM). Scanning electron microscopy (SEM) was used to investigate the morphology of the samples. The novelty of this work is advancing the scientific understanding of the effect of milling time on the particle size distribution and crystalline structure, and also understanding the effect of the spark plasma sintering on the different properties of the bulks. Densified cermet samples were produced from the nanocrystalline powders, milled for 5, 10 and 20 hours by SPS process at 1800 degrees for 5 min under a pressure of 80 MPa. Phase changes of the produced cermets were examined according to XRD, SEM/EDX analyses. Significant amounts of Cr and Fe elements were detected, especially in the 20 h milled cermet. The bulk forms of the milled powders for 5 and 20 h had a relative density of 98.43 and 98.51 %, respectively. However, 5 h milled cermet had 93.3 HRA because of the more homogeneous distribution of the (Ti,Cr)C phase, the low iron content and high relative density. According to the 0.0011 mm/year corrosion rate, and 371.68 kΩ*cm2 charge transfer resistance obtained from the potentiodynamic polarization and EIS tests, the 20 h cermet was the specimen with the highest corrosion resistance.

Dense nanostructured carbides existing in ternary system Ti-Cr-C were elaborated thanks to a two-steps method. In the first step, nanostructured Ti0.9Cr0.1C carbides were prepared by high-energy planetary ball milling under various times (5, 10, and 20 h), starting from an elemental powder mixture of titanium, chromium, and graphite. In the second step, these nanostructured powders were used to produce densified carbides thanks to the spark plasma sintering (SPS) process under a pressure of 80 MPa. The temperature was fixed at 1800 °C and the holding time was fixed at 5 min. Microstructural characteristics of the samples were investigated using X-ray diffraction (XRD). Scanning electron microscopy (SEM) coupled with energy-dispersive X-ray spectroscopy (EDX) was used to investigate the morphology and elemental composition of the samples obtained using SPS. The novelty of this work is to understand the effect of SPS on the microstructural and electrochemical properties of the nanostructured Ti0.9Cr0.1C carbides. The XRD results showed that, during sintering process, the (Ti,Cr)C carbide was decomposed into TiC, Cr7C3, and Cr3C2 phases. An amount of iron was detected as contamination during milling, especially in the case of a sample obtained from 20 h milled carbide. The bulk obtained from the milled powders for 5 and 20 h present similar relative densities of 98.43 and 98.51%, respectively. However, the 5 h milled sample shows slightly higher hardness (93.3 HRA compared to 91.5 HRA) because of the more homogeneous distribution of the (Ti,Cr)C phases and the low iron amount. According to the 0.0011 mm/year corrosion rate and 371.68 kΩ.cm2 charge transfer resistance obtained from the potentiodynamic polarization and EIS tests, the 20 h carbide was the specimen with the highest corrosion resistance.

(i) Objective: The present study aimed to compare the electrochemical corrosion resistance of six different types of fixed lingual retainer wires used as fixed retention appliances in an in vitro study. (ii) Methods: In the study, two different Ringer solutions, with pH 7 and pH 3.5, were used. Six groups were formed with five retainer wires in each group. In addition, 3-braided stainless steel, 6-braided stainless steel, Titanium Grade 1, Titanium Grade 5, Gold, and Dead Soft retainer wires were used. The corrosion current density (icorr), corrosion rate (CR), and polarization resistance (Rp) were determined from the Tafel polarization curves. (iii) Results: The corrosion current density of the Gold retainer group was statistically higher than the other retainer groups in both solutions (p < 0.05). The corrosion rate of the Dead Soft retainer group was statistically higher than the other retainer groups in both solutions (p < 0.05). The polarization resistance of the Titanium Grade 5 retainer group was statistically higher than the other retainer groups in both solutions (p < 0.05). As a result of Scanning Electron Microscope (SEM) images, pitting corrosion was not observed in the Titanium Grade 1, Titanium Grade 5 and Gold retainer groups, while pitting corrosion was observed in the other groups. (iv) Conclusion: From a corrosion perspective, although the study needs to be evaluated in vivo, the Titanium Grade 5 retainer group included is in this in vitro study may be more suitable for clinical use due to its high electrochemical corrosion resistance and the lack of pitting corrosion observed in the SEM images.