No abstract

Hard graft pays off for Henry: An efficient acid–base bifunctional mesoporous catalyst was prepared by one‐step post‐synthesis grafting of aminoorganoalkoxysilane groups on mesoporous silica (see picture). The catalyst led to yields of over 99 % in the Henry reaction (nitroaldol condensation) of p‐hydroxybenzaldehyde and nitromethane to form nitrostyrene.

We report that the polarity and dielectric constants of solvents used for grafting organosilanes on mesoporous materials strongly affect the concentration of grafted organic groups, the degree of their site-isolation, and the catalytic properties of the resulting materials. Polar and nonpolar organosilanes as well as polar-protic, dipolar-aprotic, and nonpolar solvents were investigated. Polar-protic solvents, which have high dielectric constants, resulted in smaller concentrations ( approximately 1-2 mmol/g) of polar organic groups such as 3-aminopropyl groups, higher surface area materials, site-isolated organic groups, and more efficient catalytic properties toward the Henry reaction of p-hydroxybenzaldehyde with nitromethane. On the other hand, dipolar-aprotic and nonpolar solvents resulted in larger concentrations ( approximately 2-3 mmol/g) of grafted polar functional groups, lower-to-higher surface area materials, more densely populated catalytic groups, and poor-to-efficient catalytic properties toward the Henry reaction. Both the polar-protic and dipolar-aprotic solvents resulted in significantly lower concentration of grafted groups for nonpolar organosilanes such as (3-mercaptopropyl)trimethoxysilane compared to corresponding grafting of the polar amino-organosilanes. The relationship between the solvent properties and the percentage and degree of site-isolation of the grafted functional groups was attributed to differences in solvation of the organosilanes and silanols in various solvents and possible hydrogen-bonding between the organsilanes and the solvents. The degree of site-isolation of the amine groups, which affect the material's catalytic properties, was elucidated by a new colorimetric method involving probing of the absorption maxima (lambdamax) on the d-d electronic spectrum of Cu2+ complexes with the amine-functionalized materials and the colors of the samples. The absorption lambdamax and the colors of the materials were found to be uniquely dependent on the type of solvents used for grafting the organoamines. For instance, the monoamine- and diamine-functionalized samples grafted in methanol resulted in pale blue and light purple colors with lambdamax at approximately 720 and 650 nm, respectively. These correspond to CuNO5 and CuN2O4 structures, respectively, which are indicative of the presence of site-isolated organoamines in samples grafted in methanol. The monoamine and diamine samples grafted in toluene resulted in purple and deep purple colors with lambdamax at approximately 590 and 630 nm, respectively. These correspond to CuN2O4 and CuN4O2, which are indicative of the presence of closely spaced organoamines in samples grafted in toluene. The samples grafted in isopropanol gave colors and lambdamax intermediate between those of samples grafted in toluene and methanol.

Over the past few decades the fabrication of nanoscale materials for use in chemical sensing, biomedical and biological analyses has proven a promising avenue. Nanomaterials show promise in such chemical and biological analysis mainly due to their highly tunable size- and shape-dependent chemical and physical properties. Furthermore, they exhibit unique surface chemistry, thermal stability, high surface area and large pore volume per unit mass that can be exploited for sensor fabrication. This review will discuss the chemical and physical properties of nanomaterials necessary for use as chemosensors and biosensors. It will also highlight some noteworthy recent avenues using nanoscale materials as scaffolds for chemosensing and biosensing. Nanomaterials that have proven to be useful for the fabrication of sensors, as reviewed herein, have compositions including metals, metal oxides, chalcogenides and polymers. Their structures range from nanoparticles, nanorods, and nanowires to nanoporous and core-shells. Examples of the different types of structures and compositions as well as sensors and biosensors fabricated from them will be described. Some nanomaterials are functionalized with various kinds of ligands and bioactive groups to produce sensitive and selective sensors for specific analytes. The combination of two or more types of nanostructures with core-shell type nanoassemblies and other composite structures, in addition to advantageous features enhancing sensitivity and response time of related sensors, are also discussed.

We studied the effect of two types of mesoporous silica nanoparticles, MCM-41 and SBA-15, on mitochondrial O 2 consumption (respiration) in HL-60 (myeloid) cells, Jurkat (lymphoid) cells, and isolated mitochondria. SBA-15 inhibited cellular respiration at 25-500 microg/mL; the inhibition was concentration-dependent and time-dependent. The cellular ATP profile paralleled that of respiration. MCM-41 had no noticeable effect on respiration rate. In cells depleted of metabolic fuels, 50 microg/mL SBA-15 delayed the onset of glucose-supported respiration by 12 min and 200 microg/mL SBA-15 by 34 min; MCM-41 also delayed the onset of glucose-supported respiration. Neither SBA-15 nor MCM-41 affected cellular glutathione. Both nanoparticles inhibited respiration of isolated mitochondria and submitochondrial particles.