Slab models are simple and useful structural descriptions which have long been used to describe lyotropic lamellar phases, such as lipid bilayers. Typically, slab models assume a midline symmetry and break a bilayer structure into three pieces, a central solvent-free core and two symmetric outer layers composed of the soluble portion of the amphiphile and associated solvent. This breakdown matches reasonably well to the distribution of neutron scattering length density and therefore is a convenient and common approach for the treatment of small-angle scattering data. Here, an implementation of this model within the SasView software suite is reported. The implementation is intended to provide physical consistency through the area per amphiphile molecule and number of solvent molecules included within the solvent-exposed outer layer. The proper use of this model requires knowledge of (or good estimates for) the amphiphile and solvent molecule volume and atomic composition, ultimately providing a self-consistent data treatment with only two free parameters: the lateral area per amphiphile molecule and the number of solvent molecules included in the outer region per amphiphile molecule. The use of this code is demonstrated in the fitting of standard lipid bilayer data sets, obtaining structural parameters consistent with prior literature and illustrating the typical and ideal cases of fitting for neutron scattering data obtained using single or multiple contrast conditions. While demonstrated here for lipid bilayers, this model is intended for general application to block copolymers, surfactants, and other lyotropic lamellar phase structures for which a slab model is able to reasonably estimate the neutron scattering length density/electron-density profile of inner and outer layers of the lamellae.

The shear viscous response of water is closely associated with changes in network connectivity on the sub ps timescale. The bulk viscous response is shown here to be associated with local density fluctuations and rotational motion around 1–3 ps.

Amphiphilic co-solvents can have a significant impact on the structure, organization and physical properties of lipid bilayers. Describing the mutual impact of partitioning and induced structure changes is therefore a crucial consideration for a range of topics such as anesthesia and other pharmacokinetic effects, as well as microbial solvent tolerance in the production of biofuels and other fermentation products, where molecules such as ethanol, butanol or acetic acid might be generated. Small-angle neutron scattering (SANS) is a key method for studying lipid and polymer bilayer structures, with many models for extracting bilayer structure (thickness, area per lipid etc.) from scattering data in use today. However, the molecular details of co-solvent partitioning are conflated with induced changes to bilayer structure, making interpretation and modeling of the scattering curves a challenge with the existing set of models. To address this, a model of a bilayer structure is presented which invokes a two-term partition constant accounting for the localization of the co-solvent within the bilayer. This model was validated using a series of SANS measurements of lipid vesicles in the presence of the co-solvent tetrahydrofuran (THF), showing several strategies of how to deploy the two-parameter partition constant model to describe scattering data and extract both structure and partitioning information from the data. Molecular dynamics simulations are then used to evaluate assumptions of the model, provide additional molecular scale details and illustrate its complementary nature to the data fitting procedure. This approach results in estimates of the partition coefficient for THF in 1,2-dimyristoyl-sn-glycero-3-phosphocholine at 35°C, along with an estimate of the fraction of THF residing in the hydrophobic core of the membrane. The authors envision that this model will be applicable to a wide range of other bilayer/amphiphile interactions and provide the associated code needed to implement this model as a fitting algorithm for scattering data in the SasView suite.

Assessing the structure of living microbial cell membranes is a challenging analytical goal. The cell membrane is defined by its transverse structure, an approximately 5 nm-thick selectively permeable bilayer that serves many important cellular functions. Compositionally complex, dynamic, and organized in both the transverse and lateral dimensions, understanding the cell membrane structure—and the role that structure plays in cellular function, communication, and environmental sensing is an active scientific effort. Previously, we have devised a novel isotopic labeling approach for membrane lipids to enable direct in vivo structural studies of the cell membrane in the Gram-positive bacterium, Bacillus subtilis, using small-angle neutron scattering. This was accomplished through a genetic inhibition of fatty acid (FA) degradation (ΔfadN) and a chemical inhibition of FA biosynthesis using cerulenin, an irreversible inhibitor of type II fatty acid synthases. Here, we improve upon the previous system by introducing a dCas9/sgRNA-fabF complex that blocks transcription of the essential fabF gene when under xylose induction. This leads to greater sensitivity to cerulenin in the mutant strain (JEBS102) and more robust cell growth when supplementary FAs are introduced to the culture medium. A subtle change in FA uptake is noted when compared to the prior labeling strategy. This is seen in the gas chromatography/mass spectrometry (GC/MS) data as a higher ratio of n16:0 to a15:0, and manifests in an apparent increase in the membrane thickness determined via neutron scattering. This represents an improved method of isotopic labeling for the cell membrane of Bacillus subtilis; enabling improved investigations of cellular uptake and utilization of FAs, cell membrane structure and organization as a phenotypic response to metabolic and environmental changes.

Biofuels are an increasing part of the sustainable energy picture. This makes it a societal and economic imperative to optimize biofuel production. Mitigating the toxic effects of amphiphilic co-solvents is one way to improve the efficiency of biofuel production. Amphiphiles partition into cellular membranes, leading to membrane thinning, destabilization, loss of membrane potential, and, ultimately, cell death. However, this picture of solvent toxicity misses the disruptive impact of co-solvents on lateral membrane organization, which is increasingly recognized as critical for membrane protein sorting and oligomerization. The alteration or disruption of membrane domains has deleterious effects on cellular processes. In this work, we pursue the hypothesis that membrane lateral organization is disrupted by the presence of co-solvents at concentrations lower than those which lead to full membrane destabilization. The disruption occurs due to an increasing interfacial tension between the co-existing phases, resulting in conformational changes to minimize the interfacial length-to-area ratio. This represents an unrecognized mode of solvent-induced stress and a new target for interventions to improve fermentation yields.