No abstract

Broken kernels are among the by-products of processing cashew nuts which have less commercial value. The present work aimed to obtain a cashew kernel protein concentrate from broken kernels, and then characterize it as well as using it in a vegetable burger formulation. The concentrate was obtained by isoelectric precipitation at four different pHs and subsequent drying. Higher yield was 58.6% of proteins (pH 4.0 and 4.5). The concentrate showed Water Absorption Capacity (WAC) of 1.85 mL/g and Oil Absorption Capacity (OAC) of 1.06 mL/g, as well as low solubility in aqueous medium and low foaming capacity. The concentrate was used in vegetable burger production as a substitute for soybean protein. The burgers were submitted to sensory evaluation and obtained an average of 6.6 on a nine-point scale, thus being within the acceptance zone. Regarding the purchase intent, 60% of the judges would probably or would certainly buy the product. Therefore, the cashew kernel protein concentrate can be used as a protein ingredient for food formulation. Producing cashew kernel protein concentrate allows the use of broken kernels generated in the cashew nut industrial process.

The environmental damage caused by plastic packaging and the need to reduce pollution requires actions to substitute plastic materials for more sustainable and biodegradable materials. Starch, gelatin, and bacterial cellulose films are three potential biodegradable polymeric films for use in packaging. However, these materials need improvements in their physical, chemical, and mechanical properties to be used in packaging. In this work, these films were treated with cold plasma to evaluate the effects of treatment conditions on several physical, chemical, and mechanical properties. The dielectric barrier discharge plasma technology was applied with varying treatment times (0 to 20 min) and excitation frequencies (50 to 900 Hz) at 20 kV. The optimal excitation frequency for starch films (50 Hz) was different from the optimal frequency for gelatin and bacterial cellulose films (900 Hz), indicating a high dependency on the treatment in this variable that is often neglected. Plasma treatment improved the hydrophobicity, surface morphology, water resistance, and mechanical properties of all three films, with the advantage of not recurring to chemical or biological additives.

The study aimed to evaluate the effect of black sesame andflaxseed flour addition in different proportions on bread quality.The bread formulations were developed through the RotationalCentral Composite Design (RCCD). The independent variableswere: black sesame and flaxseed flour which incorporated inamounts from 25.85% to 54.15%. The effect of the ingredients onbread quality was evaluated through physical parameters (specificvolume, expansion index and volume produced). Statisticalanalysis was performed using response surface methodology andthe two formulations with better technical performance weresubmitted to proximate composition (moisture, protein, fat, ash,carbohydrates and calcium), crumb structure, scanning electronmicroscopy (SEM) and sensorial analysis. It has been found thatblack sesame promotes greater reductions in the mass expansioncapacity than flax meal. There was an improvement in thenutritional value of the loaves by increasing the protein content,ashes, fat and calcium, in addition to the reduction ofcarbohydrates. The breads developed had good acceptability in allevaluated attributes. In this way, the inclusion of black sesameand flaxseed flour as ingredients in bread formulations promotesproducts with technological and sensorial quality.

This study evaluated the effects of dielectric barrier discharge (DBD) plasma technology on some physicochemical and structural properties of corn starch. Amylose content, solubility, water absorption index, turbidity, structural relationships, and surface morphology were measured at 100, 200, and 300 Hz excitation frequencies and at 10 and 20 min exposure times. The plasma treatment at 200 Hz and 20 min promoted the most significant modifications in amylose content, solubility, the water absorption index, and surface morphology. Turbidity did not change significantly. The surface of the granule became smoother with the presence of pores. Slight changes were observed in the ordered structure of starch. Plasma changed several physicochemical properties, significantly decreasing the amylose to amylopectin ratio. Plasma treatment at 200 Hz is recommended to increase the amylopectin content in starches.