Rapid Auger recombination represents an important challenge faced by quasi-2D perovskites, which induces resulting perovskite light-emitting diodes’ (PeLEDs) efficiency roll-off. In principle, Auger recombination rate is proportional to materials’ exciton binding energy (Eb). Thus, Auger recombination can be suppressed by reducing the corresponding materials’ Eb. Here, a polar molecule, p-fluorophenethylammonium, is employed to generate quasi-2D perovskites with reduced Eb. Recombination kinetics reveal the Auger recombination rate does decrease to one-order-of magnitude lower compared to its PEA+ analogues. After effective passivation, nonradiative recombination is greatly suppressed, which enables resulting films to exhibit outstanding photoluminescence quantum yields in a broad range of excitation density. We herein demonstrate the very efficient PeLEDs with a peak external quantum efficiency of 20.36%. More importantly, devices exhibit a record luminance of 82,480 cd m−2 due to the suppressed efficiency roll-off, which represent one of the brightest visible PeLEDs yet.

Device performance and in particular device stability for blue perovskite light-emitting diodes (PeLEDs) remain considerable challenges for the whole community. In this manuscript, we conceive an approach by tuning the ‘A-site’ cation composition of perovskites to develop blue-emitters. We herein report a Rubidium-Cesium alloyed, quasi-two-dimensional perovskite and demonstrate its great potential for pure-blue PeLED applications. Composition engineering and in-situ passivation are conducted to further improve the material’s emission property and stabilities. Consequently, we get a prominent film photoluminescence quantum yield of around 82% under low excitation density. Encouraged by these findings, we finally achieve a spectra-stable blue PeLED with the peak external quantum efficiency of 1.35% and a half-lifetime of 14.5 min, representing the most efficient and stable pure-blue PeLEDs reported so far. The strategy is also demonstrated to be able to generate efficient perovskite blue emitters and PeLEDs in the whole blue spectral region (from 454 to 492 nm).

Chiral quasi‐2D perovskite single crystals (SCs) were investigated for their circular polarized light (CPL) detecting capability. Quasi‐2D chiral perovskites, [(R)‐β‐MPA]2MAPb2I7 ((R)‐β‐MPA=(R)‐(+)‐β‐methylphenethylamine, MA=methylammonium), have intrinsic chirality and the capability to distinguish different polarization states of CPL photons. Corresponding quasi‐2D SCs CPL photodetector exhibit excellent detection performance. In particular, our device responsivity is almost one order of magnitude higher than the reported 2D perovskite CPL detectors to date. The crystallization dynamics of the film were modulated to facilitate its carrier transport. Parallel oriented perovskite films with a homogeneous energy landscape is crucial to maximize the carrier collection efficiency. The photodetector also exhibits superior mechanical flexibility and durability, representing a promising candidate for sensitive and robust CPL photodetectors.

Great successes have been achieved in developing perovskite light-emitting devices (LEDs) with blue, green, red, and near-infrared emissions. However, as key optoelectronic devices, yellow-colored perovskite LEDs remain challenging, mainly due to the inevitable halide separation in mixed halide perovskites under high bias, causing undesired color change of devices. In addition to this color-missing problem, the intrinsic toxicity and poor stability of conventional lead-halide perovskites also restrict their practical applications. We herein report the fabrication of stable yellow LEDs based on a ternary copper halide CsCu2I3, addressing the color instability and toxicity issues facing current perovskite yellow LED’s compromise. Joint experiment–theory characterizations indicate that the yellow electroluminescence originates from the broadband emission of self-trapped excitons centered at 550 nm as well as the comparable and reasonably low carrier effective masses favorable for charge transport. With a maximum luminance of 47.5 cd/m2 and an external quantum efficiency of 0.17%, the fabricated yellow LEDs exhibit a long half-lifetime of 5.2 h at 25 °C and still function properly at 60 °C with a half-lifetime of 2.2 h, which benefits from the superior resistance of CsCu2I3 to heat, moisture, and oxidation in ambient environmental conditions. The results obtained promise the copper halides with broadband light emission as an environment-friendly and stable yellow emitter for the LEDs compatible with practical applications.

Reduced-dimensional (quasi-2D) perovskite materials are widely applied for perovskite photovoltaics due to their remarkable environmental stability. However, their device performance still lags far behind traditional three dimensional perovskites, particularly high open circuit voltage (V oc) loss. Here, inhomogeneous energy landscape is pointed out to be the sole reason, which introduces extra energy loss, creates band tail states and inhibits minority carrier transport. We thus propose to form homogeneous energy landscape to overcome the problem. A synergistic approach is conceived, by taking advantage of material structure and crystallization kinetic engineering. Accordingly, with the help of density functional theory guided material design, (aminomethyl) piperidinium quasi-2D perovskites are selected. The lowest energy distribution and homogeneous energy landscape are achieved through carefully regulating their crystallization kinetics. We conclude that homogeneous energy landscape significantly reduces the Shockley-Read-Hall recombination and suppresses the quasi-Fermi level splitting, which is crucial to achieve high V oc .