Plastic debris is widespread in the environment, but information on the effects of microplastics on terrestrial fauna is completely lacking. Here, we studied the survival and fitness of the earthworm Lumbricus terrestris (Oligochaeta, Lumbricidae) exposed to microplastics (Polyethylene, <150 μm) in litter at concentrations of 7, 28, 45, and 60% dry weight, percentages that, after bioturbation, translate to 0.2 to 1.2% in bulk soil. Mortality after 60 days was higher at 28, 45, and 60% of microplastics in the litter than at 7% w/w and in the control (0%). Growth rate was significantly reduced at 28, 45, and 60% w/w microplastics, compared to the 7% and control treatments. Due to the digestion of ingested organic matter, microplastic was concentrated in cast, especially at the lowest dose (i.e., 7% in litter) because that dose had the highest proportion of digestible organic matter. Whereas 50 percent of the microplastics had a size of <50 μm in the original litter, 90 percent of the microplastics in the casts was <50 μm in all treatments, which suggests size-selective egestion by the earthworms. These concentration-transport and size-selection mechanisms may have important implications for fate and risk of microplastic in terrestrial ecosystems.

Small-scale portable rainfall simulators are an essential research tool for investigating the process dynamics of soil erosion and surface hydrology. There is no standardisation of rainfall simulation and such rainfall simulators differ in design, rainfall intensities, rain spectra and research questions, which impede drawing a meaningful comparison between results. Nevertheless, these data become progressively important for soil erosion assessment and therefore, the basis for decision-makers in application-oriented erosion protection.

No abstract

This article introduces a simple and cost-saving method developed to extract, distinguish and quantify light density microplastics of polyethylene (PE) and polypropylene (PP) in soil. A floatation method using distilled water was used to extract the light density microplastics from soil samples. Microplastics and impurities were identified using a heating method (3-5s at 130°C). The number and size of particles were determined using a camera (Leica DFC 425) connected to a microscope (Leica wild M3C, Type S, simple light, 6.4×). Quantification of the microplastics was conducted using a developed model. Results showed that the floatation method was effective in extracting microplastics from soils, with recovery rates of approximately 90%. After being exposed to heat, the microplastics in the soil samples melted and were transformed into circular transparent particles while other impurities, such as organic matter and silicates were not changed by the heat. Regression analysis of microplastics weight and particle volume (a calculation based on image J software analysis) after heating showed the best fit (y=1.14x+0.46, R=99%, p<0.001). Recovery rates based on the empirical model method were >80%. Results from field samples collected from North-western China prove that our method of repetitive floatation and heating can be used to extract, distinguish and quantify light density polyethylene microplastics in soils. Microplastics mass can be evaluated using the empirical model.

The set‐up and characterisation of an indoor nozzle‐type rainfall simulator (RS) at Wageningen University, the Netherlands, are presented. It is equipped with four Lechler nozzles (two nr. 460·788 and two nr. 461·008). The tilting irrigation plot is 6 m long and 2·5 m wide. An electrical pump supplies the constant flow during the experiments. The spatial distribution of the rainfall was measured with 60 rain gauges equally distributed on the experimental plot. Thies® Laser Precipitation Monitor was used to measure the size and falling velocity of the raindrops. Four different flow rates were applied (Q1–4). From the collected data, spatial rainfall intensity and spatial kinetic energy distribution maps were created; Christiansen uniformity coefficient was calculated for each flow rate. The results of the experiments revealed that the rainfall parameters (spatial rainfall intensity, kinetic energy, raindrop size distribution and fall velocity) in the RS are not homogeneous (Christiansen uniformity ranges from 68·5% to 83·2%). Accordingly, the whole plot can only be irrigated irregularly applying a wide range of intensities and rainfall energies. The RS offers a good opportunity to study great variety of process intensities such as splash erosion, runoff generation, soil aggregate stability, organic matter migration and scaled landscape development. Copyright © 2015 John Wiley & Sons, Ltd.