Fast and cost-efficient detection and identification of bacteria in food and water samples and biological fluids is an important challenge in bioanalytical chemistry. It was shown recently that bacteria can be detected by measuring the decrease in the diffusion current to the ultramicroelectrode caused by cell collisions with its surface. To add selectivity to the bacteria detection, herein we show the possibility of collision experiments with the signal produced by electrochemical activity of bacterial cells reducing (or oxidizing) redox species. The mediator oxidation/reduction rate can be used to identify different types of bacteria based on their specific redox activities. Here we report the analysis of electrochemical collision transients produced by two kinds of bacteria, Escherichia coli and Stenotrophomonas maltophilia. The effects of the charge and redox activity of bacterial cells on collision events are discussed. The current transients due to live cell collisions were compared to those produced by bacteria killed either by heavy metal ions (cobalt) or by an antibiotic (colistin). This approach is potentially useful for evaluating the effectiveness of antimicrobial agents. Finite-element simulations were carried out to model collision transients.

The several outstanding properties of boron‐doped diamond electrodes (BDDEs) have allowed their application for various purposes, among them electrochemical sensing. However, the electrochemical response of many redox species on BDDEs can be strongly dependent on whether their surfaces are predominantly hydrogen‐ (HT) or oxygen‐terminated (OT). Fortuitously, electrochemical pretreatments themselves can be used to enrich in situ the BDEE surface in one or the other type of termination. The surface of a cathodically pretreated BBDE (CPT‐BDDE) becomes enriched in HTs, whereas that of an anodically pretreated BDDE (APT‐BDEE) becomes enriched in OTs. Thus, when suitable, the electrochemical activity of a BDDE for a given analyte may be tuned by electrochemical pretreatments, yielding enhanced sensing properties. The main purpose of this review is the compilation and discussion of papers published after 2009 reporting on electroanalytical applications based on a CPT‐BDDE or an APT‐BDDE. Procedures to perform proper electrochemical pretreatments are also discussed.

The electrochemical response of many redox species on boron-doped diamond (BDD) electrodes can be strongly dependent on the type of chemical termination on their surface, hydrogen (HT-BDD) or oxygen (OT-BDD). For instance, on an HT-BDD electrode the [Fe(CN)6](3-/4-) redox system presents a reversible voltammetric behavior, whereas the oxidation overpotential of ascorbic acid (AA) is significantly decreased. Moreover, the electrochemical activity of BDD electrodes can be significantly affected by electrochemical pretreatments, with cathodic pretreatments (CPTs) leading to redox behaviors associated with HT-BDD. Here we report on the effect of increasingly severe CPTs on the electrochemical activity of a highly doped BDD electrode, assessed with the [Fe(CN)6](3-/4-) and AA redox probes, and on the atomic bonding structure on the BDD surface, assessed by XPS. The hydrogenation level of the BDD surface was increased by CPTs, leading to decreases of the total relative level of oxidation of the BDD surface of up to 36%. Contrary to what is commonly assumed, we show that BDD surfaces do not need to be highly hydrogenated to ensure that a reversible voltammetric behavior is obtained for Fe(CN)6](3-/4-); after a CPT, this was attained even when the total relative level of oxidation on the BDD surface was about 15%. At the same time, the overpotential for AA oxidation was confirmed as being very sensitive to the level of oxidation of the BDD surface, a behavior that might allow the use of AA as a secondary indicator of the relative atomic bonding structure on the BDD surface.

The electrochemical pretreatment of diamond microelectrodes was investigated for the purpose of learning how an anodic, cathodic or a combined anodic + cathodic polarization affects the charge-transfer kinetics for two surface-sensitive redox systems: ferri/ferrocyanide and serotonin (5-hydroxytryptamine, 5-HT). The pretreatments were performed in 0.5 mol L−1 H2SO4. The anodic pretreatment was performed galvanically for 30 s at 250 mA cm−2. The 10 cathodic pretreatment was performed for 180 s at −250 mA cm−2. The combined pretreatment involved application of the anodic step first followed by the cathodic step. The results clearly demonstrate that the best performance for both redox systems is obtained after the cathodic polarization, which presumably activates the electrode by cleaning the surface and removing site-blocking surface carbon-oxygen functionalities. The cathodic pretreatment was found to be effective at activating a fouled microelectrode in situ. This observation has important implication for the measurement of 5-HT in the bowel.