An on-line predictor of the time to disruption has been installed on the ASDEX Upgrade tokamak. It is suitable either for avoidance of disruptions or for mitigation of those that are unavoidable. The prediction uses a neural network trained on eight plasma parameters and their time derivatives extracted from 99 disruptive discharges. The network was tested off-line over 500 discharges and was found to work reliably and to be able to predict the majority of the disruptions. The trained network was installed on-line, tested over 128 discharges and used to inject killer pellets to mitigate the disruption loads.

Recent experiments at ASDEX Upgrade have achieved advanced scenarios with high β N (>3) and confinement enhancement over ITER98(y, 2) scaling, H H98y2 = 1.1-1.5, in steady state. These discharges have been obtained in a modified divertor configuration for ASDEX Upgrade, allowing operation at higher triangularity, and with a changed neutral beam injection (NBI) system, for a more tangential, off-axis beam deposition. The figure of merit, β N H ITER89-P , reaches up to 7.5 for several seconds in plasmas approaching stationary conditions. These advanced tokamak discharges have low magnetic shear in the centre, with q on-axis near 1, and edge safety factor, q 95 in the range 3.3-4.5. This q-profile is sustained by the bootstrap current, NBI-driven current and fishbone activity in the core. The off-axis heating leads to a strong peaking of the density profile and impurity accumulation in the core. This can be avoided by adding some central heating from ion cyclotron resonance heating or electron cyclotron resonance heating, since the temperature profiles are stiff in this advanced scenario (no internal transport barrier). Using a combination of NBI and gas fuelling line, average densities up to 80-90% of the Greenwald density are achieved, maintaining good confinement. The best integrated results in terms of confinement, stability and ability to operate at high density are obtained in highly shaped configurations, near double null, with δ = 0.43. At the highest densities, a strong reduction of the edge localized mode activity similar to type II activity is observed, providing a steady power load on the divertor, in the range of 6 MW m −2 , despite the high input power used (>10 MW).

The ASDEX Upgrade (AUG) programme is directed towards physics input to critical elements of the ITER design and the preparation of ITER operation, as well as addressing physics issues for a future DEMO design. Since 2015, AUG is equipped with a new pair of 3-strap ICRF antennas, which were designed for a reduction of tungsten release during ICRF operation. As predicted, a factor two reduction on the ICRF-induced W plasma content could be achieved by the reduction of the sheath voltage at the antenna limiters via the compensation of the image currents of the central and side straps in the antenna frame. There are two main operational scenario lines in AUG. Experiments with low collisionality, which comprise current drive, ELM mitigation/suppression and fast ion physics, are mainly done with freshly boronized walls to reduce the tungsten influx at these high edge temperature conditions. Full ELM suppression and non-inductive operation up to a plasma current of I p = 0.8 MA could be obtained at low plasma density. Plasma exhaust is studied under conditions of high neutral divertor pressure and separatrix electron density, where a fresh boronization is not required. Substantial progress could be achieved for the understanding of the confinement degradation by strong D puffing and the improvement with nitrogen or carbon seeding. Inward/outward shifts of the electron density profile relative to the temperature profile effect the edge stability via the pressure profile changes and lead to improved/decreased pedestal performance. Seeding and D gas puffing are found to effect the core fueling via changes in a region of high density on the high field side (HFSHD). The integration of all above mentioned operational scenarios will be feasible and naturally obtained in a large device where the edge is more opaque for neutrals and higher plasma temperatures provide a lower collisionality. The combination of exhaust control with pellet fueling has been successfully demonstrated. High divertor enrichment values of nitrogen E N ⩾ 10 have been obtained during pellet injection, which is a prerequisite for the simultaneous achievement of good core plasma purity and high divertor radiation levels. Impurity accumulation observed in the all-metal AUG device caused by the strong neoclassical inward transport of tungsten in the pedestal is expected to be relieved by the higher neoclassical temperature screening in larger devices.

No abstract

The ablation of carbon pellets injected into ECR-heated plasmas of Wendelstein 7-AS (W7-AS) has been investigated using a photographic technique with the aim of studying features of the ablation process in stellarator plasmas. The ablation rate profiles were measured assuming a proportionality of the C II radiation and the ablation rate. This assumption was confirmed experimentally and by simulations performed by a quasi-three-dimensional code. The fraction of continuum radiation, which is detected together with the C II line radiation (when using the light filters with finite spectral width), did not affect these measurements.No significant drifts of pellet clouds in the toroidal, poloidal and radial directions were observed in the C II line (723 nm) emission. From fast electron temperature measurements ( t = 10 µs) using ECE diagnostics, no indications of a pre-cooling wave were found.A difference between the ablation rates for discharges with low and high plasma density, which lies beyond the error bars, was observed. A specific zone of enhanced ablation was detected at the plasma periphery at high density. The appearance of such ablation enhancement, points to the existence of an additional local heat flux. However, the mechanism that could explain the enhanced ablation phenomena at high plasma densities remains unclear.