The evolution of microstructure and crystallographic texture has been investigated in double-sided friction stir welded microalloyed steel, using electron backscatter diffraction (EBSD). The microstructure analyses show that the centre of stirred zone reached a temperature between Ac 1 -Ac 3 during FSW, resulting in a dual phase austenitic/ ferritic microstructure. The temperatures in the thermo-mechanically affected zone and the overlapped area between the first and second weld pass did not exceed the Ac 1 . The shear generated by the rotation probe occurs in austenitic/ferritic phase field where the austenite portion of the microstructure is transformed to a bainitic ferrite, on cooling. Analysis of crystallographic textures with regard to shear flow lines generated by the probe tool, show the dominance of simple shear components across the whole weld. The austenite texture at Ac 1 -Ac 3 is dominated by the B and simple shear texture components, where the bainite phase textures formed on cooling were inherited from the shear textures of the austenite phase with relatively strong variant selection. The ferrite portion of the stirred zone and the ferrites in the thermo-mechanically affected zones and the overlapped area underwent shear deformation with textures dominated by the D 1 and D 2 simple shear texture components. The formation of ultra-fine equiaxed ferrite with submicron grain size has been observed in the overlapped area between the first and second weld pass. This is due to continuous dynamic strain-induced recrystallisation as a result of simultaneous severe shear deformation and drastic undercooling.

Grain boundary engineering has been proposed to increase the lifetime performance of sensitized austenitic stainless steel in aggressive environments. Increased microstructure resistance is typically associated with higher fractions of twin (Sigma3) grain boundaries, but there is uncertainty about the properties and role of other boundaries. To develop predictive models for stress corrosion crack nucleation, more information is required about how grain boundary crystallography and the orientations of the grain boundary plane and its surrounding grains affect crack development. Digital image correlation combined with electron backscatter diffraction has been used to characterize the microstructure and to observe, in situ, the nucleation and propagation of short stress corrosion cracks in thermo-mechanically processed type 304 stainless steel. The crack path and its growth rate have been determined and are found to be influenced by the microstructure.

Intergranular stress corrosion cracking (IGSCC) in austenitic stainless steels occurs at susceptible grain boundaries after sensitisation. In this study, the effects of test duration, static stress (applied and residual) and microstructure orientation on the developed populations of short crack nuclei are reported for a sensitised type 304 austenitic stainless steel in an acidified potassium tetrathionate (K2S4O6 ) solution. The crack populations were analysed using the Gumbel distribution method, showing an increase in the characteristic crack lengths with increasing time and grain size. There is a weak, but measurable effect of stress on crack length. Tensile stress increases crack growth and compressive residual stresses introduced by surface machining are shown to be beneficial. A significant dependence on sample orientation is observed and this cannot be explained in terms of the bulk microstructure properties or characteristics, which showed no significant variations

Designing microstructure of components made from Inconel 718 nickel based superalloy (IN718) with tailored mechanical properties for high temperature applications, require sequential thermo-mechanical processing. This often includes straining and annealing at solution annealing temperature (i.e. ≈980℃) followed by water quenching and subsequent aging heat treatments at lower temperatures. In addition to the microstructure development (i.e. precipitation) the aging heat treatment partially relieve the residual stresses generated at previous stages of forging and water quenching, however the stress field will not be completely relaxed. In this study, a series of experiments were conducted on round tensile specimens made from IN718 bar to investigate tensile stress relaxation behaviours at elevated temperatures used for aging heat treatments. The stress relaxation curves obtained can be described by a hyperbolic function with a non-zero asymptotic stress (σ∞), which seems to be proportional to the initially applied stress (σ0) for a fixed temperature. This behaviour is investigated at temperatures between 620℃ and 770℃ that is a temperature range used in industry to perform the aging heat treatments to obtain microstructures with tailored mechanical properties. It has been shown that the σ∞/ σ0 ratio has decreased rapidly with increasing temperature at this range. The relaxation behaviour has been assessed numerically and an empirical relationship has been defined for each temperature that can be used for modelling purposes

The evolution of residual stress and microstructure has been investigated in electron-beam welded Ti-6Al-4V alloy rings in order to develop an understanding of how the distribution of through-thickness residual stress correlates with microstructural evolution. A multiple technique approach to residual stress measurement was employed using a combination of different measurement techniques including X-ray diffraction (XRD), hole drilling method based on electronic speckle pattern interferometry (ESPI), and the contour method. It was found that there is a strong correlation between the change in residual stress and alpha phase morphology across the weld. The fusion zone exhibited highly tensile residual stress which was typified by an entirely acicular α′ microstructure formed by a displacive transformation within prior β grains on cooling. The tensile residual stress in the centre of the weld reduced towards the heat affected zone, transitioning to a compressive residual stress upon increasing distance from the weld centre. The transition from tensile to compressive residual stress correlates with a significant decrease in the volume fraction of α′ and an increase in the bimodal morphology of equiaxed primary alpha in a diffusional transformed beta matrix leading to elongated alpha in the base material