A multiporous electrochemical sensor for epinephrine recognition and detection based on molecularly imprinted polypyrrole

Zhou, Hong; Xu, Guilin; Zhu, Anhong; Zhao, Zhe; Ren, Chengcheng; Nie, Linlin; Kan, Xianwen

doi:10.1039/c2ra20787g

Cited by 64 publications

(38 citation statements)

References 44 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…In that direction, recently, a few reports described the use of this dropcoating approach to prepare electrodes coated by highly organized macroporous MIP films. These electrodes were used for electrochemical determination of Hg(II) [27], dopamine [28], and adrenaline [29]. Advantageously, the signal enhancement for the macroporous MIP film modified electrodes was promising (Table 1).…”

Section: Pattern-supported Macroporous Mip Filmsmentioning

confidence: 99%

“…Instead, cracks or other defects in the colloidal crystal deposited that way are unavoidable. Hence, this procedure was more frequently used to prepare a colloidal crystal assembly on a small-size electrode surface [27][28][29]. In that direction, recently, a few reports described the use of this dropcoating approach to prepare electrodes coated by highly organized macroporous MIP films.…”

Section: Pattern-supported Macroporous Mip Filmsmentioning

confidence: 99%

See 1 more Smart Citation

Surface development of molecularly imprinted polymer films to enhance sensing signals

Sharma

Dąbrowski

D’Souza

et al. 2013

TrAC Trends in Analytical Chemistry

106

View full text Add to dashboard Cite

Section: Pattern-supported Macroporous Mip Filmsmentioning

confidence: 99%

Section: Pattern-supported Macroporous Mip Filmsmentioning

confidence: 99%

Surface development of molecularly imprinted polymer films to enhance sensing signals

Sharma

Dąbrowski

D’Souza

et al. 2013

TrAC Trends in Analytical Chemistry

106

View full text Add to dashboard Cite

“…Polypyrrole (PPy) is especially promising conducting polymers in the field of electrochemical sensors fabrication. In comparison with several conducting polymers, PPy possesses a high environmental stability, an easy synthesis and a higher electrical conductivity .…”

Section: Introductionmentioning

confidence: 99%

A Facile Strategy for Construction of Sensor for Detection of Ondansetron and Investigation of its Redox Behavior and Thermodynamic Parameters

et al. 2018

View full text Add to dashboard Cite

A sodium dodecylsulfate‐doped polypyrrole (SDS‐PPy) film was elaborated on glassy carbon electrode (GCE) by an electrodeposition method in phosphate buffer solution (pH 2.0) containing pyrrole (Py) and sodium dodecyl sulfate (SDS). SDS‐PPy/GCE was used for the construction of sensor, which showed excellent electrochemical response for the detection of ondansetron (OND) compared to conventional PPy. The application of the square wave (SW), with the adsorptive accumulation, indicates a maximum response at 1.33 V in H2SO4 (0.5 M). The influence of experimental parameters on determination of OND is discussed. The adsorptive stripping technique showed to be more sensitive, giving responses twice as big as those of non‐accumulated OND. The substantial improvement of response permits the development of an electroanalytical technique with a linear concentration in the range (1.0–80 μM), low detection (0.09 μM), and quantification limits (0.3 μM), and acceptable relative standard deviations of repeatability (0.59 %), and reproducibility (1.51 %). Consequently, this electrode is promising candidate for an accurate electroanalytical determination of OND in pharmaceutical samples with high sensitivity and selectivity, good accuracy and precision. The electrooxidation of OND at SDS‐PPy/GCE at various temperatures were studied by cyclic voltammetry to evaluate both the kinetic (ks and Ea) and thermodynamic (ΔG*, ΔH* and ΔS*) parameters.

show abstract

“…Zhou et al reported an electrochemical sensor based on molecularly imprinted PPy for epinephrine recognition [77]. Pyrrole was electropolymerized with epinephrine on the surface of an electrode coated with silica nanoparticles and CNTs.…”

Section: Biosensorsmentioning

confidence: 99%

Conducting Polymers in Sensor Design

Sołoducho¹,

Cabaj²

2016

Conducting Polymers

View full text Add to dashboard Cite

Conducting polymers (CPs) as well as conducting polymer nanoparticles seem to be very applicable for the development of various analyte-recognizing elements of sensors and biosensors. This chapter reviews mainly fabrication methods as well as application of conducting polymers in sensors. Conducting polymers (CPs) have been applied in the design of catalytic and affinity biosensors as immobilization matrixes, signal transduction systems, and even analyte-recognizing components. Various types of conducting and electrochemically generated polymer-based electrochemical sensors were developed including amperometric catalytic and potentiodynamic affinity sensors. A very specific interaction of analyte with immobilized biological element results in the formation of reaction products.

show abstract

A multiporous electrochemical sensor for epinephrine recognition and detection based on molecularly imprinted polypyrrole

Cited by 64 publications

References 44 publications

Surface development of molecularly imprinted polymer films to enhance sensing signals

Surface development of molecularly imprinted polymer films to enhance sensing signals

A Facile Strategy for Construction of Sensor for Detection of Ondansetron and Investigation of its Redox Behavior and Thermodynamic Parameters

Conducting Polymers in Sensor Design

Contact Info

Product

Resources

About