A review on conventional and advanced minimum quantity lubrication approaches on performance measures of grinding process

Gupta, Munish Kumar; Khan, Aqib Mashood; Song, Qinghua; Wang, Qingqing; Khalid, Qazi Salman; Jamil, Muhammad; Kuntoğlu, Mustafa; Usca, Üsame Ali; Sarıkaya, Murat; Pimenov, Danil Yurievich

doi:10.1007/s00170-021-07785-x

Cited by 67 publications

(25 citation statements)

References 149 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The conclusions presented in these papers show that the MQL method may, under certain processing conditions, be an alternative to the flood method. These conclusions are also confirmed by other studies [30,31], which show that the MQL method can improve the effectiveness of the GF reaching the contact zone between active abrasive grains and the ground surface and thus reducing the risk of an unfavorable thermal impact on the top layer.…”

Section: Introductionsupporting

confidence: 83%

The Influence of the Depth of Grinding on the Condition of the Surface Layer of 20MnCr5 Steel Ground with the Minimum Quantity Lubrication (MQL) Method

et al. 2022

View full text Add to dashboard Cite

This paper describes the research on abrasive machining conditions and their influence on microhardness and residual stresses distribution in the technological surface layer of 20MnCr5 steel. The roughness of ground samples was also measured. Samples underwent a vacuum carburizing process (LPC) followed by high-pressure gas quenching (HPGQ) in a 4D quenching chamber. Processes were realized with a single-piece flow method. Then, the flat surfaces of samples were ground with a Vortex type IPA60EH20VTX alumina grinding wheel using a flat-surface grinder. The samples were ground to three depths of grinding (ae = 0.01; 0.02; 0.03 mm) with grinding fluid supply using either flood method (WET) or minimum quantity lubrication (MQL) method. The condition of the technological surface layer was described using microhardness and residual stresses, as well as some selected parameters of surface roughness. The results obtained revealed that changes in microhardness as compared to microhardness of the material before grinding were lower in samples ground with grinding fluid supplied with MQL method. At the same time, the values of residual stresses were also better for samples ground using MQL method. Furthermore, the use of grinding fluid fed with MQL method produced lower values of surface roughness compared to the parameters obtained with WET method. It was concluded that for the tested scope of machining conditions, the MQL method can be a favourable alternative to the flood method of supplying grinding fluid into the grinding zone.

show abstract

Section: Introductionsupporting

confidence: 83%

The Influence of the Depth of Grinding on the Condition of the Surface Layer of 20MnCr5 Steel Ground with the Minimum Quantity Lubrication (MQL) Method

et al. 2022

View full text Add to dashboard Cite

show abstract

“…The samples were machined under dry and MQL conditions because today's manufacturing industry is very much focused on environmental protection [47] and a reduction in the consumption of machining fluids [48]. Furthermore, MQL has been successfully applied to improve the machinability of difficult-to-cut materials [49,50]. In the MQL method, we used ECOCUT MIKRO 20 E oil, which was produced by mixing with air.…”

Section: Workpiece Details and Preparationmentioning

confidence: 99%

Corrosion Resistance and Surface Bioactivity of Ti6Al4V Alloy after Finish Turning under Ecological Cutting Conditions

et al. 2021

Self Cite

View full text Add to dashboard Cite

The influence of cooling conditions and surface topography after finish turning of Ti6Al4V titanium alloy on corrosion resistance and surface bioactivity was analyzed. The samples were machined under dry and minimum quantity lubrication (MQL) conditions to obtain different surface roughness. The surface topographies of the processed samples were assessed and measured using an optical profilometer. The produced samples were subjected to electrochemical impedance spectroscopy (EIS) and corrosion potential tests (Ecorr) in the presence of simulated body fluid (SBF). The surface bioactivity of the samples was assessed on the basis of images from scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS) analysis. The inspection of the surfaces of samples after turning under dry and MQL conditions revealed unevenly distributed precipitation of hydroxyapatite compounds (Ca/P) with a molar ratio in the range of 1.73–1.97. Regardless of the cutting conditions and surface roughness, the highest values of Ecorr ~0 mV were recorded on day 7 of immersion in the SBF solution. The impedance characteristics showed that, compared to the MQL conditions, surfaces machined under dry conditions were characterized by greater resistance and the presence of a passive layer on the processed surface. The main novelty of the paper is the study of the effect of ecological machining conditions, namely, dry and MQL cutting on the corrosion resistance and surface bioactivity of Ti6Al4V titanium alloy after finish turning. The obtained research results have practical significance. They can be used by engineers during the development of technological processes for medical devices made of Ti6Al4V alloy to obtain favorable functional properties of these devices.

show abstract

“…MQL utilization brings reduction in cutting coolant which causes less environmental impact. MQL improves life of tool, enhance surface roughness than conventional/lubrication system [7][8][9].…”

Section: Mql/near Dry Machiningmentioning

confidence: 99%

State of the art review on the sustainable dry machining of advanced materials for multifaceted engineering applications: progressive advancements and directions for future prospects

Singh

Gill²,

Dogra³

et al. 2022

Mater. Res. Express

View full text Add to dashboard Cite

In this article, the comprehensive review on the application, and indeed, a comparative analysis on dry machining of different types of materials (Inconel, steel, aluminum, cast iron, magnesium and advanced materials) used in machining (turning, drilling and milling operations) were carried out in the light of utmost works published in the literature. The work describes the scientific findings of the past twenty years, including sustainable methods (surface texture, solid lubricants, vibration-assisted machining, laser-assisted machining), tool coatings, and geometry of tools. Vibration-assisted machining is another direction that researchers have investigated without the use of cutting coolants, where the complete disposal of coolants is not possible. Various researchers have carried out rigorous experimental work on milling, drilling, and turning operations under dry conditions to machine numerous materials. A significant proportion of experimental data about tool wear, tool wear machining, surface quality, surface integrity, etc., has been analyzed under dry conditions. However, the critical analysis of dry machining for different conventional machining operations for a variety of industrial materials is still lacking for establishing dry machining as a sustainable process for industrial applications. Thus, the critical analysis of various machining parameters and their consequences on tool wear and the surface quality of machined work was carried out in this work. Finally, scientific recommendations based on critical findings were proposed for industrial implementation of dry machining.

show abstract

A review on conventional and advanced minimum quantity lubrication approaches on performance measures of grinding process

Cited by 67 publications

References 149 publications

The Influence of the Depth of Grinding on the Condition of the Surface Layer of 20MnCr5 Steel Ground with the Minimum Quantity Lubrication (MQL) Method

The Influence of the Depth of Grinding on the Condition of the Surface Layer of 20MnCr5 Steel Ground with the Minimum Quantity Lubrication (MQL) Method

Corrosion Resistance and Surface Bioactivity of Ti6Al4V Alloy after Finish Turning under Ecological Cutting Conditions

State of the art review on the sustainable dry machining of advanced materials for multifaceted engineering applications: progressive advancements and directions for future prospects

Contact Info

Product

Resources

About