A superhydrophobic polyacrylate film with good durability fabricated via spray coating

Guo, Danyi; Chen, Jiahui; Lei, Wen; Wang, Peng; Xu, Shanhui; Cheng, Jiang; Wen, Xiufang; Wang, Shuangfeng; Huang, Can; Pi, Pihui

doi:10.1007/s10853-018-2730-5

Cited by 15 publications

(2 citation statements)

References 55 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Over the past decade, 316L stainless steel has been widely used in the fields of orthopedic implants, dental implants, and cardiovascular stents due to its suitable mechanical properties, excellent corrosion resistance, and cost effectiveness [1][2][3]. However, its poor pitting-resistance property imposes limitations on its application.…”

Section: Introductionmentioning

confidence: 99%

Effect of Hafnium Addition on the Microstructure and Property Evolutions of ZrCN Coating Prepared via Physical Vapor Deposition

Wang

Pei

Deng³

et al. 2023

Coatings

View full text Add to dashboard Cite

In this paper, Zr(Hf)xCN coatings were deposited onto 316L stainless steel (316L SS) substrates at 400 °C using the radio-frequency (R.F.) magnetron sputtering technique with Hf-Zr-C composite target materials. The influence of Hf element content on microstructure, mechanical properties, and corrosion resistance and platelet interaction with the surface of Zr(Hf)xCN coatings were then investigated. The results indicate that the microstructure, mechanical properties, and corrosion resistance of coatings depend on their chemical composition. Corrosion resistance and platelet interaction with the surface could be improved by adding Hf to the Zr2CN. By optimizing the Hf-Zr-C ratio, Zr(Hf)xCN coatings with excellent corrosion resistance were obtained. The ZrHfCN-3 coating with a Hf element content of 7.33% possesses excellent mechanical properties and good corrosion resistance. The result of the platelet interaction with the surface confirms that Zr(Hf)xCN coatings have better platelet interaction with the surface than 316L SS.

show abstract

Section: Introductionmentioning

confidence: 99%

Effect of Hafnium Addition on the Microstructure and Property Evolutions of ZrCN Coating Prepared via Physical Vapor Deposition

Wang

Pei

Deng³

et al. 2023

Coatings

View full text Add to dashboard Cite

show abstract

“…It has been reported that polymers with low surface energy, such as polyacrylate (PA) [17,18], polystyrene (PS) [19,20], polyvinylidene fluoride (PVDF) [21,22], poly(dimethylsiloxanes) (PDMS) [23,24], epoxy [25,26], poly(methacrylic acid) (PMAA) [27,28], polyurethane (PU) [29][30][31], and have been used to fabricate superhydrophobic coatings. However, the water contact angle of these polymers is generally less than 120 • on a homogeneous flat surfaces.…”

Section: Introductionmentioning

confidence: 99%

Investigation of the Effects of Component Ratios on the Properties of Superhydrophobic Polyurethane/Fluorinated Acrylic Co-Polymer/SiO2 Nanocomposite Coatings

Ke¹,

Zhang³

et al. 2021

Coatings

View full text Add to dashboard Cite

In this work, polyurethane/fluorinated acrylic co-polymer/silicon dioxide (PU/FAP/SiO2) hybrid superhydrophobic coatings were fabricated on glass substrates via a simple one-step coating process. The effects of each coating component on the coating properties were systematically investigated. The optimized coating exhibits a water contact angle (WCA) of 159° and a rolling angle of 3°. Meanwhile, the coating has an optical light transmittance of 88%, indicating the good transparency of the coating. Besides, the coating demonstrates an adequate level of abrasion resistance. After a total abrasion distance of 300 cm against a piece of 800 mesh sand paper, the sample still kept a water contact angle of about 110°, showing its high abrasion resistance. Therefore, the optimized coating has a great potential for practical application.

show abstract

Superhydrophobic Materials Derived from Hybrid Silicon Copolymers

Loh

et al. 2020

Silicon Containing Hybrid Copolymers

View full text Add to dashboard Cite

A superhydrophobic polyacrylate film with good durability fabricated via spray coating

Cited by 15 publications

References 55 publications

Effect of Hafnium Addition on the Microstructure and Property Evolutions of ZrCN Coating Prepared via Physical Vapor Deposition

Effect of Hafnium Addition on the Microstructure and Property Evolutions of ZrCN Coating Prepared via Physical Vapor Deposition

Investigation of the Effects of Component Ratios on the Properties of Superhydrophobic Polyurethane/Fluorinated Acrylic Co-Polymer/SiO2 Nanocomposite Coatings

Superhydrophobic Materials Derived from Hybrid Silicon Copolymers

Contact Info

Product

Resources

About