Adding Aramid Fibers to Improve Tribological Characteristics of two Polymers

Botan, Mihail; Musteata, Andreea Elena; Ionescu, Traian Florian; Georgescu, Constantin; Deleanu, Lorena

doi:10.24874/ti.2017.39.03.02

Search citation statements

Order By: Relevance

Paper Sections

Select...

Literature Review and Problem Statement1

Introduction1

Citation Types

Supporting

Mentioning

Contrasting

Year Published

2019

2022

Publication Types

Select...

Article4

Relationship

Self Cite0

Independent4

Authors

Journals

Cited by 4 publications

(2 citation statements)

References 13 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The use of wear-resistant polymers is an important niche for conducting tribological studies into a change in the characteristics of composites. The increase in wear resistance was revealed when using acrylonitrile butadiene styrene alumina [22]. It is necessary to establish temperature modes at friction under the modes of dry lubrication.…”

Section: Literature Review and Problem Statementmentioning

confidence: 99%

Analysis of tribological efficiency of movable junctions "polymericcomposite materials ‒ steel"

Аулин

Derkach

Makarenko

et al. 2019

EEJET

View full text Add to dashboard Cite

Section: Literature Review and Problem Statementmentioning

confidence: 99%

Analysis of tribological efficiency of movable junctions "polymericcomposite materials ‒ steel"

Аулин

Derkach

Makarenko

et al. 2019

EEJET

View full text Add to dashboard Cite

“…Research studies on tribological behavior of PBT as matrix with glass beads or short aramid fibers were reported in Georgescu et al [ 32 ] and Botan et al [ 33 , 34 ], only for a sliding distance of 5000 m.…”

Section: Introductionmentioning

confidence: 99%

Tribology of Polymer Blends PBT + PTFE

et al. 2021

View full text Add to dashboard Cite

This paper presents results on tribological characteristics for polymer blends made of polybutylene terephthalate (PBT) and polytetrafluoroethylene (PTFE). This blend is relatively new in research as PBT has restricted processability because of its processing temperature near the degradation one. Tests were done block-on-ring tribotester, in dry regime, the variables being the PTFE concentration (0%, 5%, 10% and 15% wt) and the sliding regime parameters (load: 1, 2.5 and 5 N, the sliding speed: 0.25, 0.5 and 0.75 m/s, and the sliding distance: 2500, 5000 and 7500 m). Results are encouraging as PBT as neat polymer has very good tribological characteristics in terms of friction coefficient and wear rate. SEM investigation reveals a quite uniform dispersion of PTFE drops in the PBT matrix. Either considered a composite or a blend, the mixture PBT + 15% PTFE exhibits a very good tribological behavior, the resulting material gathering both stable and low friction coefficient and a linear wear rate lower than each component when tested under the same conditions.

show abstract

Exceptional performance of bi-directionally reinforced composite of PEEK manufactured by commingling technique using poly(p-phenylene-benzobisoxazole) (PBO) fibers

Padhan

Marathe²,

Bijwe³

2022

Composites Science and Technology

View full text Add to dashboard Cite

Adding Aramid Fibers to Improve Tribological Characteristics of two Polymers

Abstract: A B S T R A C T

Cited by 4 publications

References 13 publications

Analysis of tribological efficiency of movable junctions "polymericcomposite materials ‒ steel"

Analysis of tribological efficiency of movable junctions "polymericcomposite materials ‒ steel"

Tribology of Polymer Blends PBT + PTFE

Exceptional performance of bi-directionally reinforced composite of PEEK manufactured by commingling technique using poly(p-phenylene-benzobisoxazole) (PBO) fibers

Contact Info

Product

Resources

About

Adding Aramid Fibers to Improve Tribological Characteristics of two Polymers

Abstract: A B S T R A C T

Cited by 4 publications

References 13 publications

Analysis of tribological efficiency of movable junctions "polymeric­composite materials ‒ steel"

Analysis of tribological efficiency of movable junctions "polymeric­composite materials ‒ steel"

Tribology of Polymer Blends PBT + PTFE

Exceptional performance of bi-directionally reinforced composite of PEEK manufactured by commingling technique using poly(p-phenylene-benzobisoxazole) (PBO) fibers

Contact Info

Product

Resources

About

Analysis of tribological efficiency of movable junctions "polymericcomposite materials ‒ steel"

Analysis of tribological efficiency of movable junctions "polymericcomposite materials ‒ steel"