Analysis of Power Generating Speed Bumps Made of Concrete Foam Composite

Syam, Bustami; Muttaqin, Maraghi; Hastrino, D; Sebayang, Alexander; Basuki, WS; Sabri, M.; Abda, Syahrul

doi:10.1088/1757-899x/180/1/012033

Cited by 7 publications

(4 citation statements)

References 1 publication

Supporting

Mentioning

Contrasting

Order By: Relevance

“…In this study we choose the type B4 [2] in which the physical and mechanical properties of the material shown in Table 1. The material has been extensively used of some light structures, such as tiles [3] and speed bump [4]. The conduit covers geometry and dimensions were modelled as shown Figure 6 and 7.…”

Section: 1materialsmentioning

confidence: 99%

Mechanical Response of Open Channel Cover Made of Concrete Foam Due to External Loadings

Syam

Sebayang

Gunawan³

et al. 2017

J. Phys.: Conf. Ser.

View full text Add to dashboard Cite

Abstract. Open channel conduit is commonly constructed on side roadway, car park area, etc., with the aims to collect rainwater or seapage water. To avoid garbages following the waterflow, the conduit is equipped with adequate cover. In addition, the cover can also be functioned for temporary car park area. Thus, the conduit cover should strong enough to sustain external loading. This paper discusses the design and response of the conduit cover using finite element software ANSYS MECHANICAL version 17.5.

show abstract

Section: 1materialsmentioning

confidence: 99%

Mechanical Response of Open Channel Cover Made of Concrete Foam Due to External Loadings

Syam

Sebayang

Gunawan³

et al. 2017

J. Phys.: Conf. Ser.

View full text Add to dashboard Cite

show abstract

“…(1) increases the uptake of surface water [4]; (2) allows us to convert organic waste into compost; (3) improves soil fertility. It is hoped that the technology to manufacture bioporous composite pipes with permeable pores could serve as a solution for reducing flood hazards, especially in parking lots and parking areas [5,6].…”

Section: Introductionmentioning

confidence: 99%

Analysis and Computer Simulation of Biopore Tubes Made of Concrete Foam Reinforced by Durian Skin Fiber

et al. 2023

View full text Add to dashboard Cite

This research was conducted to utilize durian skin waste into useful materials by maximizing its utilization to solve environmental problems. The idea is to process the fibers so that they can be used as composite reinforcement material. Here, the durian fibers are used as fillers for foam concrete. The so-called concrete foam composite is designed and manufactured to produce tubes utilized for biopore systems. Biopore tube materials were tested and the tubes are also subjected to field tests to check their response subjected to static loading. A series of computer simulations are conducted. Results are compared with other biopore tubes (PVC and concrete). The simulation results show that the concentration of stresses is obviously seen around the hole located in the middle and upper section of the tubes. However, at those critical points in the tubes, the stresses are of smaller than that of the strength of the tubes. We conclude that biopore tubes with 16 holes in total provided on the tube wall are still feasible to be produced.

show abstract

“…The main parameters used in the static structural simulation include the selected meshing size, the selection of fixed support and the magnitude of the load received by the speed bumps. Simulations were carried out on Ansys software using the Finite Element Analysis (FEA) [8]- [13] method. Static structural analysis using Ansys Workbench [14].…”

Section: Introductionmentioning

confidence: 99%

Static Simulation on Speed bumps Made of Foam Concrete Foam with Durian Skin Fibers Using Ansys Software

Muttaqin

2022

JMESI

View full text Add to dashboard Cite

Motorcyclists find speed bumps problematic because they require them to slow down. A concept comes to create a technology and can use a power plant with a generator driving source from speed bumps in its application. The product is designed and made on a big scale to allow all cars going through speed bumps. Because it is important to handle the kinetic energy generated from the vehicle in order for it to be transformed into electricity and connected to the load. Several tests, such as static and impact testing, are performed on the speed bump to get a material that is resistant to structural integrity. Simulation was used to perform static and impact testing using ansys software. As for the material, durian skin is very suitable as a mixture of materials, because it contains fibers that can be used for concrete reinforcement. Also obtained the equivalent stress of 0.05 MPa. The x-Axis voltage is 0.01MPa. The y-axis stress is 0.04 MPa. The results of this study can be concluded that the concrete composite reinforced with durian skin fiber also has the potential to be used as a speed bump power generator.

show abstract

Analysis of Power Generating Speed Bumps Made of Concrete Foam Composite

Cited by 7 publications

References 1 publication

Mechanical Response of Open Channel Cover Made of Concrete Foam Due to External Loadings

Mechanical Response of Open Channel Cover Made of Concrete Foam Due to External Loadings

Analysis and Computer Simulation of Biopore Tubes Made of Concrete Foam Reinforced by Durian Skin Fiber

Static Simulation on Speed bumps Made of Foam Concrete Foam with Durian Skin Fibers Using Ansys Software

Contact Info

Product

Resources

About