Continuous Fabrication of Meter‐Scale Single‐Wall Carbon Nanotube Films and their Use in Flexible and Transparent Integrated Circuits

Wang, Bingwei; Song, Jang‐Kun; Zhu, Qian‐Bing; Sun, Yun; Luan, Jian; Hou, Peng‐Xiang; Qiu, Song; Li, Qingwen; Liu, Chang; Sun, Dongming; Cheng, Hui‐Ming

doi:10.1002/adma.201802057

Cited by 73 publications

(56 citation statements)

References 73 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The carbon nanotube film was obtained via the continuous fabrication of meter-scale single-walled carbon nanotube film [39], reported in our previous work, which was collected on a filter membrane.…”

Section: Methodsmentioning

confidence: 99%

Flexible Pressure Sensors with a Wide Detection Range Based on Self-Assembled Polystyrene Microspheres

Chen

Wang²,

Zhu

et al. 2019

Sensors

View full text Add to dashboard Cite

Flexible pressure sensors are important components of electronic skin and flexible wearable devices. Most existing piezoresistive flexible pressure sensors have obtained high sensitivities, however, they have relatively small pressure detection ranges. Here, we report flexible pressure sensors with a wide detection range using polydimethylsiloxane (PDMS) as the substrate, carbon nanotube films as the electrode material, and self-assembled polystyrene microsphere film as the microstructure layer. The obtained pressure sensor had a sandwich structure, and had a wide pressure detection range (from 4 kPa to 270 kPa), a sensitivity of 2.49 kPa−1, and a response time of tens of milliseconds. Two hundred load–unload cycles indicated that the device had good stability. In addition, the sensor was obtained by large-area fabrication with a low power consumption. This pressure sensor is expected to be widely used in applications such as electronic skin and flexible wearable devices.

show abstract

Section: Methodsmentioning

confidence: 99%

Flexible Pressure Sensors with a Wide Detection Range Based on Self-Assembled Polystyrene Microspheres

Chen

Wang²,

Zhu

et al. 2019

Sensors

View full text Add to dashboard Cite

show abstract

“…However, through AuCl3 treatment, the pristine value was reduced to ca. 57 Ω/sq, which is one of the lowest sheet resistances recorded (at 90% T) for SWCNT TCFs [13,16,41,42]. Previously reported SWCNT TCFs fabricated by the dry method [6,10,13,16,[41][42][43] were selected for comparison with the TCFs in this work ( Fig.…”

Section: Dopant Effect and Comparison Of Performance And Yield With Rmentioning

confidence: 99%

High-performance transparent conducting films of long single-walled carbon nanotubes synthesized from toluene alone

et al. 2019

View full text Add to dashboard Cite

Single-walled carbon nanotube (SWCNT) transparent conducting films (TCFs) are attracting increasing attention due to their exceptional optoelectronic properties. Toluene is a proposed carbon source for SWCNT synthesis, but the growth parameters of SWCNTs and their TCF optoelectronic performance (i.e., sheet resistance versus transmittance) have been insufficiently evaluated. Here, we have for the first time reported a systematic study of the fabrication of high-performance SWCNT TCFs using toluene alone as the carbon source. The mechanisms behind each observed phenomenon were elucidated using optical and microscopy techniques. By optimizing the growth parameters, high yields of SWCNT TCFs exhibiting a considerably low sheet resistance of 57 Ω/sq at 90% transmittance were obtained. This competitive optoelectronic performance is mainly attributable to long SWCNT bundles (mean length is 41.4 μm) in the film. Additionally, a chirality map determined by electron diffraction displays a bimodal distribution of chiral angles divided at 15°, which is close to both armchair and zigzag edges. Our study paved the way towards scaled-up production of SWCNTs for the fabrication of high-performance TCFs for industrial applications.

show abstract

Section: Intrinsically Conductive Materialsmentioning

confidence: 99%

Design and applications of stretchable and self-healable conductors for soft electronics

et al. 2019

View full text Add to dashboard Cite

Soft and conformable electronics are emerging rapidly and is envisioned as the future of next-generation electronic devices where devices can be readily deployed in various environments, such as on-body, on-skin or as a biomedical implant. Modern day electronics require electrical conductors as the fundamental building block for stretchable electronic devices and systems. In this review, we will study the various strategies and methods of designing and fabricating materials which are conductive, stretchable and self-healable, and explore relevant applications such as flexible and stretchable sensors, electrodes and energy harvesters.

show abstract

Continuous Fabrication of Meter‐Scale Single‐Wall Carbon Nanotube Films and their Use in Flexible and Transparent Integrated Circuits

Cited by 73 publications

References 73 publications

Flexible Pressure Sensors with a Wide Detection Range Based on Self-Assembled Polystyrene Microspheres

Flexible Pressure Sensors with a Wide Detection Range Based on Self-Assembled Polystyrene Microspheres

High-performance transparent conducting films of long single-walled carbon nanotubes synthesized from toluene alone

Design and applications of stretchable and self-healable conductors for soft electronics

Contact Info

Product

Resources

About