2013
DOI: 10.5194/acp-13-1607-2013
|View full text |Cite
|
Sign up to set email alerts
|

Determining water sources in the boundary layer from tall tower profiles of water vapor and surface water isotope ratios after a snowstorm in Colorado

Abstract: The D/H isotope ratio is used to attribute boundary layer humidity changes to the set of contributing fluxes for a case following a snowstorm in which a snow pack of about 10 cm vanished. Profiles of H<sub>2</sub>O and CO<sub>2</sub> mixing ratio, D/H isotope ratio, and several thermodynamic properties were measured from the surface to 300 m every 15 min during four winter days near Boulder, Colorado. Coeval analysis of the D/H ratios and CO<sub>2</sub> concentrations find t… Show more

Help me understand this report
View preprint versions

Search citation statements

Order By: Relevance

Paper Sections

Select...
1
1
1
1

Citation Types

4
65
0

Year Published

2013
2013
2019
2019

Publication Types

Select...
9

Relationship

1
8

Authors

Journals

citations
Cited by 53 publications
(69 citation statements)
references
References 74 publications
4
65
0
Order By: Relevance
“…The HDO depletion from 2 to 4 March 2007 corresponds to the conden-X. Zhao et al: Cyclone-induced surface ozone and HDO depletion in the Arctic (Keeling, 1958;Miller and Tans, 2003;Noone et al, 2013) can be used to estimate the δD and/or sublimation flux of blowing snow. However, isotopologue measurements for precipitation at the source region (for example, near the Beaufort Sea) are necessary to validate the results and to make meaningful comparison of measured with modelled sublimation flux.…”
Section: Model Resultsmentioning
confidence: 99%
“…The HDO depletion from 2 to 4 March 2007 corresponds to the conden-X. Zhao et al: Cyclone-induced surface ozone and HDO depletion in the Arctic (Keeling, 1958;Miller and Tans, 2003;Noone et al, 2013) can be used to estimate the δD and/or sublimation flux of blowing snow. However, isotopologue measurements for precipitation at the source region (for example, near the Beaufort Sea) are necessary to validate the results and to make meaningful comparison of measured with modelled sublimation flux.…”
Section: Model Resultsmentioning
confidence: 99%
“…The isotope partitioning approaches utilized a two end-member (E and T) mixing model, where R is the ratio of the heavy to light isotope (in this case, 18 O/ 16 O) [Yakir and Sternberg, 2000]: To solve this equation, estimates of the isotopic ratio of the ET, E, and T fluxes are needed. At both sites, the former is solved for using a modified "Keeling plot" approach as described by Noone et al [2013]. The data from each height were binned on hourly time steps to generate vertical profiles, and the three uppermost inlets (above the canopy) were used to estimate the isotopic ratio of the canopy's latent heat flux ( 18 O ET ).…”
Section: Isotope Partitioning Approach 2321 Niwot Ridgementioning
confidence: 99%
“…The ability of this simple model to describe our data and the possible contribution of regional advection is then discussed. The original Keeling approach (Keeling, 1958) was initially proposed to describe the addition of CO 2 into the atmosphere, and then further used to determine the isotopic composition of evapotranspired vapour flux (Yakir and Sternberg, 2000;Yepez et al, 2003;Williams et al, 2004;Zhang et al, 2010;Noone et al, 2011Noone et al, , 2013Griffis et al, 2013). Assuming a background represented by an initial air quantity with a mixing ratio q BG (mmol mol −1 ), and taking n A (mol) the corresponding dry air amount, the addition of water vapour n E (mmol) leads to the following mixing equation:…”
Section: Local Isotopic Signaturesmentioning
confidence: 99%