Hybrid composites under high strain rate compressive loading

Naik, N.K.; Veerraju, Ch.; Kavala, Venkateswara Rao

doi:10.1016/j.msea.2007.10.124

Cited by 44 publications

(28 citation statements)

References 52 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Among the polymeric materials reinforced with fibers, stand out the hybrid polymer composites that offer advantages in the combination of fibers used as reinforcement, producing a material with higher specific properties 1,[4][5][6] , which would be difficult to obtain using a single type of fibers reinforcement.…”

Section: Introductionmentioning

confidence: 99%

Polymer Composites Reinforced with Hybrid Fiber Fabrics

Felipe

Batista

et al. 2017

Mat. Res.

View full text Add to dashboard Cite

In an effort to show the influence of the hybridization method in hybrid fabric reinforced composites within the characteristic of the fracture and the mechanical properties, two laminate reinforced with bi-directional woven were developed, where one of them was reinforced with a hybrid strand (hybrid strand composite laminate) and the other with a different strands (hybrid fabric composite laminate). Both laminates used polyester resin, Kevlar-49 and glass-E fibers, had four layers and were prepared industrially by hand lay-up manufacturing. The percentages by weight of fiberglass and Kevlar in each type of woven are equal. The hybrid strand composite laminate showed a higher tensile strength, however the hybrid fabric composite laminate showed superior properties in three-point bending test, for example, 41.7 % superiority in flexural strength. The results showed that the hybridization method in hybrid reinforced composites influences the mechanical behavior of laminates and the formation and spread of damage.

show abstract

Section: Introductionmentioning

confidence: 99%

Polymer Composites Reinforced with Hybrid Fiber Fabrics

Felipe

Batista

et al. 2017

Mat. Res.

View full text Add to dashboard Cite

show abstract

“…Specifically, strain rate of up to 860 s À1 , 705 s À1 , 544 s À1 , 840 s À1 and 1149 s À1 has been reported by Harding [14], Gama et al [15], Hosur et al [17], Song et al [16] and Haque and Ali [5], respectively. In our recent studies on high strain rate behavior of woven fabric E-glass/epoxy composites under compressive loading [31][32][33], strain rate of up to 1997 s À1 and 2890 s À1 has been obtained along warp/fill and thickness directions, respectively. In actual practical cases, especially for impact analysis, strain rate could be very high.…”

Section: Overall Discussionmentioning

confidence: 99%

“…The bars are made of SUS440C martensite stainless steel with Young's modulus of 203 GPa and density of 7667 kg/m 3 . The details regarding design and development of compressive SHPB apparatus, specimen design and development, testing procedure, data acquisition and analysis, safety precautions to be taken and pulse shaper design are given in [29][30][31][32]. Details of data acquisition and processing are presented in Appendix A and calibration of compressive SHPB apparatus is presented in Appendix B.…”

Section: Experimental Technique and Data Acquisitionmentioning

confidence: 99%

“…From these signals and using one-dimensional wave propagation theory in elastic bars, strain rate versus time, strain versus time, stress versus time and stress versus strain history in the specimen are determined [25,31,32]. …”

Section: Experimental Technique and Data Acquisitionmentioning

confidence: 99%

“…There are typical studies on split Hopkinson pressure bar testing technique [22][23][24][25][26][27][28][29][30]. In some of our recent studies on WF composites [31][32][33] and epoxy resin [34,35], the strain rate was up to 2000 s À1 . Wang et al [36] presented an analytical method for assessing strain rate sensitivity of unidirectional composite laminates.…”

Section: Introductionmentioning

confidence: 99%

See 2 more Smart Citations

Analytical and experimental studies on mechanical behavior of composites under high strain rate compressive loading

et al. 2013

Self Cite

View full text Add to dashboard Cite

The effect of loading rates and particle geometry on compressive properties of polypropylene/zinc oxide nanocomposites: Experimental and numerical prediction

et al. 2011

View full text Add to dashboard Cite

Compressive properties, of particulate filled polymer matrix composites, are affected (to a certain extent) by the geometry of the particles, as well as the loadingrates. Therefore, this article presents the results on the compressive properties of polypropylene/zinc oxide nanocomposites across strain rates from 10−2 to 10−3 s−1. The specimens were tested using a Universal Testing Machine for static loading and a conventional Split Hopkinson Pressure Bar apparatus for dynamic loading. Results show that the yield stress and 2.5% flow stress, of both PP/ZnO nanocomposites, showed a positive increment with increasing strain rates. However, the yield strain shows a contradictory pattern, where it decreased with increasing strain rates. PP/ZnO‐white seal recorded higher strain rate sensitivity, dissipation energy, stiffness, and strength properties, than that of PP/ZnO‐pharmaceutical, over a wide range of strain rates investigated. Interestingly, the Eyring theory almost agreed with the experimental results. Overall, based on the experimental and numerical results, we do believe that particle geometry, as well as strain rates, has a significant influence on the compressive properties of polypropylene/zinc oxide nanocomposites specimens. POLYM. COMPOS., 2012. © 2011 Society of Plastics Engineers

show abstract

Hybrid composites under high strain rate compressive loading

Cited by 44 publications

References 52 publications

Polymer Composites Reinforced with Hybrid Fiber Fabrics

Polymer Composites Reinforced with Hybrid Fiber Fabrics

Analytical and experimental studies on mechanical behavior of composites under high strain rate compressive loading

The effect of loading rates and particle geometry on compressive properties of polypropylene/zinc oxide nanocomposites: Experimental and numerical prediction

Contact Info

Product

Resources

About