Lasers in Restorative Dentistry

Olivi, Giovanni; Olivi, Matteo

doi:10.1007/978-3-662-47317-7

Cited by 15 publications

(1 citation statement)

References 21 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…How the protective layer formed by desensitizing agents affects the adhesion between dental substrates and restorative materials must be considered [25][26][27]. Dentin wettability by resinous monomers of the adhesive system is fundamental to establish adhesion [7].…”

Section: Introductionmentioning

confidence: 99%

Effect of desensitizing dentifrices on eroded dentin wettability

et al. 2022

View full text Add to dashboard Cite

Objective:To analyze the wettability on the surface of eroded dentin in teeth submitted to abrasive wear with desensitizing dentifrices. Material and Methods: Bovine dentin specimens were polished and immersed in 10 mL of citric acid (pH=3.2) for 2 h. The eroded specimens were submitted to mechanic brushing according to the 4 dentifrices adopted: Colgate Total (control); Colgate Sensitive Pro-Relief; Sensodyne Repair & Protect; or Sensodyne Rapid Relief. Afterwards, it was conditioned in 37% aqueous phosphoric acid solution. Wettability of 80 specimens (n=10) brushed for 7 or 21 days was evaluated by measuring the contact angle between the dentin surface and a drop of the adhesive Single Bond Universal® (3M) with a goniometer. Changes in the surface morphology of 12 specimens (n = 3) brushed for 21 days were followed by confocal laser scanning microscopy (CLSM). Data were analyzed by two-way ANOVA and Tukey test (p > 0.05). Results: Groups treated with desensitizing dentifrices did not differ significantly (p ≤ 0.05). Surface treatment and abrasive wear did not interact significantly (p ≤ 0.05). Brushing along 7 days gave the smallest contact angle value (p ≥ 0.05). CLSM images showed morphological changes for all the groups. Conclusion: The desensitizing dentifrices did not interfere in eroded dentin wettability after brushing along 7 or 21 days. Brushing with any of the dentifrices along 21 days promoted open dentinal tubules.

show abstract

Section: Introductionmentioning

confidence: 99%

Effect of desensitizing dentifrices on eroded dentin wettability

et al. 2022

View full text Add to dashboard Cite

show abstract

Influence of pulse duration and water/air cooling ratio on the efficiency of Er:YAG 2940 nm laser in debonding of porcelain laminate veneers: An in vitro study

AlBalkhi

Hamadah

2022

Clinical & Exp Dental Res

View full text Add to dashboard Cite

Objective: To determine the effectiveness of different pulse durations (PD) and the water/air (W/A) cooling ratio of the Er:YAG 2940 nm laser that are required for debonding porcelain laminate veneers (PLV), by investigation of the needed time for PLV debonding (DT) and the changes in dental pulp temperature.Materials and Methods: Thirty-six extracted noncarious human maxillary premolars were prepared for receiving PLV. Samples were randomly assigned to six different groups, based on PD and the W/A ratio: Groups A (50 µs, 1:1), B (50 µs, 3:3), C (100 µs, 1:1), D (100 µs, 3:3), E (300 µs, 1:1), and F (300 µs, 3:3). Veneers were debonded using laser irradiation by the same parameters (270 mJ, 15 Hz) with noncontact application mode.Results: All 36 veneers were debonded. Samples of the 50 and 100 µs PDs showed significantly shorter DT (7.4−17 s) than that of the 300 µs which showed significantly the longest DT (104 s) among all other groups (p < .001). However, the highest elevation of pulp temperature was observed in Group E (300 µs, 1:1) which reached (3.4°C). Conclusion:Using the 50 or 100 µs PD of the Er:YAG laser was more efficient than 300 µs in reducing DT of PLVs with minimal change in pulp temperature. W/A cooling ratio had minimal influence on the DT of PLV.

show abstract