Monitoring Reinforced Concrete Cracking Behavior under Uniaxial Tension Using Distributed Fiber-Optic Sensing Technology

Self Cite

Distributed fiber-optic sensing (DFOS) technologies have been used for decades to detect damage in infrastructure. One recent DFOS technology, Optical Frequency Domain Reflectometry (OFDR), has attracted attention from the structural engineering community because its high spatial resolution and refined accuracy could enable new monitoring possibilities and new insight regarding the behavior of reinforced concrete (RC) structures. The current research project explores the ability and potential of OFDR to measure distributed strain in RC structures through laboratory tests on an innovative beam–column connection, in which a partial slot joint was introduced between the beam and the column to control damage. In the test specimen, fiber-optic cables were embedded in both the steel reinforcement and concrete. The specimen was tested under quasi-static cyclic loading with increasing displacement demand at the structural laboratory of the Pacific Earthquake Engineering Research (PEER) Center of UC Berkeley. Different types of fiber-optic cables were embedded both in the concrete and the rebar. The influence of the cable coating and cable position are discussed. The DFOS results are compared with traditional measurements (DIC and LVDT). The high resolution of DFOS at small deformations provides new insights regarding the mechanical behavior of the slotted RC beam–column connection, including direct measurement of beam curvature, rebar deformation, and slot opening and closing. A major contribution of this work is the quantification of the performance and limitations of the DFOS system under large cyclic strains. Performance is quantified in terms of non-valid points (which occur in large strains when the DFOS analyzer does not return a strain value), maximum strain that can be reliably measured, crack width that causes cable rupture, and the effect of the cable coating on the measurements. Structural damage indices are also proposed based on the DFOS results. These damage indices correlate reasonably well with the maximum sustained drift, indicating the potential of using DFOS for RC structural damage assessment. The experimental data set is made publicly available.

Section: Introductionmentioning

confidence: 99%

Distributed Fiber-Optic Strain Sensing of an Innovative Reinforced Concrete Beam–Column Connection

Zhang

Liu

Darwish

et al. 2022

Self Cite

“…Xu et al [ 12 ] obtained the spatiotemporal evolution characteristics of fractures in the soil strain field through the OFDR distributed strain measurement method and established the correlation between strain and fractures. Liu et al [ 13 ] deployed a distributed OFDR fiber sensing network to analyze the cracking behavior of concrete. The results revealed the relationship between the bond stress–slip behavior of concrete cracks.…”

Section: Introductionmentioning

confidence: 99%

Diagnosis and Monitoring of Tunnel Lining Defects by Using Comprehensive Geophysical Prospecting and Fiber Bragg Grating Strain Sensor

Li,

Luo

et al. 2024

Tunnel excavation induces the stress redistribution of surrounding rock. In this excavation process, the elastic strain in the rock is quickly released. When the maximum stress on the tunnel lining exceeds the concrete’s load-bearing capacity, it causes cracking of the lining. Comprehensive geophysical exploration methods, including seismic computerized tomography, the high-density electrical method, and the ultrasonic single-plane test, indicated the presence of incomplete distribution of broken rock along the tunnel axis. Based on the geophysical exploration results, a carbon-fiber-strengthened tunnel simulation model was established to analyze the mechanical characteristics of the structure and provide a theoretical basis for sensor deployment. Fiber Bragg grating (FBG) strain sensors were used to measure the stress and strain changes in the second lining concrete after carbon reinforcement. Meanwhile, one temperature sensor was installed in each section to enable temperature compensation. The monitoring results demonstrated that the stress–strain of the second lining fluctuated within a small range, and the lining did not show any crack expansion behavior, which indicated that carbon-fiber-reinforced polymer (CFRP) played an effective role in controlling the structural deformation. Therefore, the combined detection of physical exploration and FBG sensors for the structure provided an effective monitoring method for evaluating tunnel stability.

“…Xu et al [ 14 ] obtained the spatiotemporal evolution characteristics of cracks in soil strain fields using OFDR distributed strain measurement, establishing the correlation between strain and cracks. Liu et al [ 15 ] analyzed concrete cracking behavior using a distributed OFDR fiber optic sensor network. Their results revealed the relationship between concrete crack bond stress and slip behavior.…”

Section: Introductionmentioning

confidence: 99%

Assessment of Tunnel Lining Stability through Integrated Monitoring of Fiber Bragg Grating Strain and Structural Deformation

Li,

He,

et al. 2024

Tunnel excavation induces the stress redistribution of the surrounding rock. Structural cracks may develop in the secondary lining due to this stress redistribution and bias pressure, consequently affecting the overall construction safety of the tunnel. This paper aims to achieve real-time monitoring of the excavation stability of the lining structure by integrating two monitoring technologies: structural deformation monitoring and fiber grating strain monitoring. Additionally, it proposes a method to simultaneously measure the thermal strain and applied stress–strain of the structure. By analyzing the displacement and deformation of the lining structure, its stability can be preliminarily evaluated in the short term. To achieve long-term real-time monitoring and a more accurate assessment of the tunnel structure’s stability, the paper introduces fiber Bragg grating (FBG) strain sensor monitoring technology. First, based on the geological stratigraphy information obtained from the exploration, a simulation model of the tunnel under different section bias angles is established. The displacement and stress concentration areas of the lining structure are then analyzed to optimize the sensor deployment array and provide a theoretical basis for the sensor arrangement. FBG strain sensors are installed on the surface of the structure to measure thermal strain and loading stress–strain, whereas FBG temperature sensors measure local temperature. The findings indicate that following tunnel excavation, the maximum daily strain differences at K107+043 and K107+240 were 126.87 µε and 209.38 µε, respectively. After a period of rock disturbance, the average daily strain differences due to applied stress–strain were 16.8 µε and 12.65 µε, respectively. The thermal strain was close to the daily strain difference. Therefore, after the rock disturbance subsided, the strain fluctuations in the lining structure were mainly caused by local temperature changes, and the surrounding rock tended to stabilize. This offers a viable method for evaluating structural stability post-tunnel excavation.