New Development Environment for Modern Bioelectromagnetics Signal Processing Applications [Application Notes]

Gasmelseed, Akram

doi:10.1109/mmm.2013.2259404

Cited by 6 publications

(1 citation statement)

References 28 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…We present the design of the graphic programming for the control of variable loads. To give emphasis to this process, the Block Diagram is presented, followed by the Front Panel develop in LabVIEW [26][27][28][29][30][31]. The communications and control interface for the sending and receiving of data was made through LabVIEW with arduino and Maker Hub [30,[32][33].…”

Section: Control Load Systemmentioning

confidence: 99%

Design and construction of smart grid with variable load control AC and DC with LabView: off-grid case.

Martinez¹,

Martinez²,

Valdes³

2019

Proceedings of the 17th LACCEI International Multi-Conference for Engineering, Education, and Technology: “Industry, Innovation

View full text Add to dashboard Cite

The following document will show the step-by-step development that was taken into account to carry out the design and construction of smart grid scale prototype with AC and DC load control through the HMI interface with LabVIEW software. The design process of the off-grid solar system was carried out through 7 stages that framed the scale of the solar installation. Once the design of the sizing was finished, programming was carried out in Human Machine Interface (HMI) graphics environment with LabVIEW software for optimal control of AC and DC variable loads. This control was established through current relays from 5 volts to 110 volts AC and 5 volts to 12 volts DC. The control interface was made through an embedded board with NI-VISA communication. It is important to note that the smart grid control prototype "Smart Grid" shows optimal results in its operation; denoting this that from the optics of the programming done in the graphics environment, the control of loads dependent on control centers; act at disposition. Redundant this in improvements for the energy consumption derived from the storage system under the autonomy designed for three days.

show abstract

Section: Control Load Systemmentioning

confidence: 99%

Design and construction of smart grid with variable load control AC and DC with LabView: off-grid case.

Martinez¹,

Martinez²,

Valdes³

2019

Proceedings of the 17th LACCEI International Multi-Conference for Engineering, Education, and Technology: “Industry, Innovation

View full text Add to dashboard Cite

show abstract

Location of Quality Parameters in Small Smart Grid: Off-Grid Case Using Wavelet Transform

Rojas

Pacheco

et al. 2020

IOP Conf. Ser.: Mater. Sci. Eng.

View full text Add to dashboard Cite

In the following work the analysis made to an electrical signal by means of wavelet toolbox will be shown. The analysis will be done contemplating the use of the Discrete Wavelet Transform (DWT). This will show the multilevel decomposition taking into account different orders of daubechies. Taking into account the different levels it is expected to show the variants in terms of energetic quality such as sag, swell and harmonic detection. The final work will link the work of digital signal processing with previous work where the construction of a prototype solar system will be explained to obtain the electrical signals of voltage, current and power consumed. In this introductory stage will show the step-by-step development that was taken into account to carry out the design and construction of smart grid scale prototype with AC and DC load control through the HMI interface with LabVIEW software. The design process of the off-grid solar system was carried out through 7 stages that framed the scale of the solar installation. Once the design of the sizing was finished, programming was carried out in Human Machine Interface (HMI) graphics environment with LabVIEW software for optimal control of AC and DC variable loads. This control was established through current relays from 5 volts to 110 volts AC and 5 volts to 12 volts DC. The control interface was made through an embedded board with NI-VISA communication. It is important to note that the smart grid control prototype “Smart Grid” shows optimal results in its operation; denoting this that from the optics of the programming done in the graphics environment, the control of loads dependent on control canter’s; act at disposition. Redundant this in improvements for the energy consumption derived from the storage system under the autonomy designed for three days.

show abstract

2D Application of FDTD Technique with NI LabVIEW

Yurt

Torpi

2019

2019 6th International Conference on Electrical and Electronics Engineering (ICEEE)

View full text Add to dashboard Cite

New Development Environment for Modern Bioelectromagnetics Signal Processing Applications [Application Notes]

Cited by 6 publications

References 28 publications

Design and construction of smart grid with variable load control AC and DC with LabView: off-grid case.

Design and construction of smart grid with variable load control AC and DC with LabView: off-grid case.

Location of Quality Parameters in Small Smart Grid: Off-Grid Case Using Wavelet Transform

2D Application of FDTD Technique with NI LabVIEW

Contact Info

Product

Resources

About