Soil preparation machine parameters for the cultivation of cucurbitaceous crops

Chuyanov, Dustmurod; Shodmonov, Golib; Avazov, I; Rashidov, Nurbek; Ochilov, S

doi:10.1088/1757-899x/883/1/012122

Cited by 30 publications

(24 citation statements)

References 3 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Inside each branch pipe, movable reflective plates 6 and 7 are installed, which cut the fertilizers moving along the tool-conducting channel into parts, followed by their direction to the corresponding soil horizon. The reflective plates of the conductive channel do not completely block it, so some of the fertilizers enter the lower distributor of 8 [25][26][27].…”

Section: Methodsmentioning

confidence: 99%

See 1 more Smart Citation

Traction resistance of a ripper with a current distribution line

et al. 2021

View full text Add to dashboard Cite

The pipeline distributor carries out deep loosening of the soil and three-tier fertilization. The study aims to determine the traction resistance of the working body of the ripper with a distribution pipe. The study uses the basic provisions of mathematics, theoretical mechanics, and agricultural mechanics. The method of calculating the traction resistance of the cultivator-fertilizer equipped with pipelines-distributors for three-tier fertilization is presented. The components of the balance of traction resistance are determined. Analytical dependencies are obtained for determining the traction resistance of the working body of the ripper with a distribution pipe. It has been established that the traction of the ripper working body with the fertilizer distributor depends on the physical and mechanical properties of the soil, the blade thickness and length of the chisel blade, the length of the working surface of the share, the angle of crumbling and the solution of the share, the width of the working body and the speed of movement. The traction resistance of the pipeline is 12-12.5% of the traction resistance of the rack and 4-5% of the total traction resistance of the ripper working body.

show abstract

Section: Methodsmentioning

confidence: 99%

“…It is known that the current line of the ripper-fertilizer must meet the following basic requirements: have a convenient layout behind the ripper working body of the ripper, ensure high-quality distribution of mineral fertilizers at specified depths [27].…”

Section: Methodsmentioning

confidence: 99%

Traction resistance of a ripper with a current distribution line

et al. 2021

View full text Add to dashboard Cite

show abstract

“…The development of machines for processing and preparing the soil for sowing melons in the conditions of Uzbekistan F.Mamatov , B.Mirzaev [4][5][6][7][8][9][10][11][12][13][14][15][16][17][18][19][20][21][22][23], N.Aldoshin [3, 10-11, 19-20, 24], U. Umurzakov [4,19], D.Chuyanov [5,27], U. Kodirov [6,24], H. Ravshanov [4][5][6], [25][26], H. Fayzullaev [5,25] and others.…”

Section: Introductionmentioning

confidence: 99%

Combination machine for soil preparation and sowing of gourds

et al. 2021

View full text Add to dashboard Cite

The purpose of the study is to substantiate the method and design scheme of a combined machine for preparing the soil and sowing melons. The authors propose a new method of soil preparation and sowing, as well as a machine for its implementation. The basic principles and methods of classical mechanics, mathematical analysis, and statistics were used in this study. The method of preparing the soil and planting gourds provides a combination of the following technological processes: the turnover of the layers of the upper layer of soil, the sowing area to the left and to the right, shallow tilling the soil of the field with the left and right sides of the sowing area, deep tillage seeding areas with simultaneous formation of irrigation furrows and the local application of fertilizers, soil preparation for sowing in line sowing and sowing seeds of melons. The machine consists of lister housings installed along the axis of symmetry of the unit, flat cutters, parallel-type deep-diggers, furrowers, coulters for fertilizing, and a sowing device. It was found that preparation of soil for sowing and planting of melons with a minimum expenditure of energy is provided by the width of Lusternik buildings 86 cm, the width of tillers and cultivators, respectively, 45 and 33 cm, the longitudinal distance between the body and the plane of 35 cm between the cultivators of 42.3 cm, and longitudinal spacing of the chisel cultivator and sowing device 110 cm.

show abstract

“…The development of new tillage technologies and the improvement of machinery to prepare crops, including gourds, is an urgent task in agriculture . The problems of developing improved tillage technologies and tillage machines are considered in many scientific papers [24][25][26][27]. Research on the development of tillage machines and machines for preparing soil for sowing crops, including gourds, and the study of the interaction of working bodies with soil were carried out by F.Mamatov , B.Mirzaev [4][5][6][7][8][9][10][11][12], [14][15][16][17][18][19][20][21], [28][29], U.Umurzakov [4,19], N.Aldoshin [3], [10][11], I.Ismoilov [3], [10][11], D.Chuyanov [5,27], U.Kodirov [6,24], H.Ravshanov [4][5], [6,20], [25][26], I.Ergashev [2,6,12,23,30], P.Berdimuratov…”

Section: Introductionmentioning

confidence: 99%

Raking plates of the combination machine's subsoiler

et al. 2021

View full text Add to dashboard Cite

The purpose of the research is to justify the type of subsoiling plates of the machine for preparing the soil for sowing melon crops. The machine designed by the authors for the preparation of the soil for sowing melon crops under the tunnel film is equipped with deep loosening subsoilers of “paraplough” type with loosening plates. The scheme of subsoiler arrangement on the frame of the machine is shown. The basic principles and methods of classical mechanics, mathematical analysis, and statistics were used in this study. The scheme of subsoiler arrangement on the frame depending on their parameters has been theoretically justified. Experimental studies have established that using a subsoiler in the form of a rod and plate with a length of 12 cm and a height of 20 cm provides the required crumbling of the soil at minimum energy consumption.

show abstract

Soil preparation machine parameters for the cultivation of cucurbitaceous crops

Cited by 30 publications

References 3 publications

Traction resistance of a ripper with a current distribution line

Traction resistance of a ripper with a current distribution line

Combination machine for soil preparation and sowing of gourds

Raking plates of the combination machine's subsoiler

Contact Info

Product

Resources

About