Thermal and visual comfort analysis of adaptive vacuum integrated switchable suspended particle device window for temperate climate

Nundy, Srijita; Ghosh, Aritra

doi:10.1016/j.renene.2019.12.004

Cited by 76 publications

(21 citation statements)

References 81 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Windows are one of the weakest components in a building. It allows external heat to come inside (enhance the air condition load), internal heat to outside (enhance heating load) and offer visual connection to building interior to exterior [172][173][174][175][176][177][178][179][180][181][182][183][184][185]. Building window systems are affected by an overall heat transfer coefficient (U-value) and solar energy transmittance (g-value) [186][187][188][189].…”

Section: Perspective and Discussionmentioning

confidence: 99%

Status of BIPV and BAPV System for Less Energy-Hungry Building in India—A Review

et al. 2020

Self Cite

View full text Add to dashboard Cite

The photovoltaic (PV) system is one of the most promising technologies that generate benevolent electricity. Therefore, fossil fuel-generated electric power plants, that emit an enormous amount of greenhouse gases, can be replaced by the PV power plant. However, due to its lower efficiency than a traditional power plant, and to generate equal amount of power, a large land area is required for the PV power plant. Also, transmission and distribution losses are intricate issues for PV power plants. Therefore, the inclusion of PV into a building is one of the holistic approaches which reduce the necessity for such large land areas. Building-integrated and building attached/applied are the two types where PV can be included in the building. Building applied/attached PV(BAPV) indicates that the PV system is added/attached or applied to a building, whereas, building integrated PV (BIPV) illustrates the concept of replacing the traditional building envelop, such as window, wall, roof by PV. In India, applying PV on a building is growing due to India’s solar mission target for 2022. In 2015, through Jawaharlal Nehru National Solar Mission, India targeted to achieve 100 GW PV power of which 40 GW will be acquired from roof-integrated PV by 2022. By the end of December 2019, India achieved 33.7 GW total installed PV power. Also, green/zero energy/and sustainable buildings are gaining significance in India due to rapid urbanization. However, BIPV system is rarely used in India which is likely due to a lack of government support and public awareness. This work reviewed the status of BIPV/BAPV system in India. The BIPV window system can probably be the suitable BIPV product for Indian context to reduce the building’s HVAC load.

show abstract

Section: Perspective and Discussionmentioning

confidence: 99%

Status of BIPV and BAPV System for Less Energy-Hungry Building in India—A Review

et al. 2020

Self Cite

View full text Add to dashboard Cite

show abstract

“…CRI values over 80 are good while over 90 are considered to be excellent [6,7]. Good CCT and CRI indicate no significant colour difference between external daylight and the transmitted daylight through the window [55]. Lower the difference better the quality of light in to an indoor space which is an essential criteria for occupant's health, interpersonal relationships and aesthetic taste [56,57].…”

Section: Visual Comfort Analysismentioning

confidence: 99%

Visual Comfort Analysis of Semi-Transparent Perovskite Based Building Integrated Photovoltaic Window for Hot Desert Climate (Riyadh, Saudi Arabia)

et al. 2021

Self Cite

View full text Add to dashboard Cite

Buildings consume considerable amount of energy to maintain comfortable interior. By allowing daylight, visual comfort inside a building is possible which can enhance the occupant’s health, mood and cognitive performance. However, traditional highly transparent windows should be replaced with semitransparent type window to attain a comfortable daylight inside a building. Evaluation of visual comfort includes both daylight glare and colour comfort analysis. Building integrated photovoltaic (BIPV) type windows are promising systems and can possess a range of semitransparent levels depending on the type of PV used. In this work, the semitransparent Perovskite BIPV windows was investigated by employing daylight glare analysis for an office building located in Riyadh, KSA and three wavelength dependent transmission spectra for colour comfort analysis. The results showed that the transmissions range between 50–70% was optimum for the comfortable daylight for south facing vertical pane BPV-windows. However, excellent colour comfort was attained for the transmission range of 90% which provided glare issues. Colour comfort for 20% transparent Perovskite was compared with contemporary other type of PV which clearly indicated that wavelength dependent transmittance is stronger over single value transmittance.

show abstract

“…The transmitted sunlight through the transparent or semi-transparent window of a building significantly influences on the visual comfort of building occupant. Besides PCE, there are some other crucial parameters such as average visible transmittance (AVT), transparency colour perception [134][135][136], corresponding colour temperature (CCT) [137,138] and colour rendering index (CRI) [139] should be investigated for optimizing the semi-transparent PSCs. Usually, AVT range between 20%-30% is required for window applications.…”

Section: Transparency and Efficiency Tradeoff Of Pscsmentioning

confidence: 99%

Perovskite Solar Cells for BIPV Application: A Review

et al. 2020

Self Cite

View full text Add to dashboard Cite

The rapid efficiency enhancement of perovskite solar cells (PSCs) make it a promising photovoltaic (PV) research, which has now drawn attention from industries and government organizations to invest for further development of PSC technology. PSC technology continuously develops into new and improved results. However, stability, toxicity, cost, material production and fabrication become the significant factors, which limits the expansion of PSCs. PSCs integration into a building in the form of building-integrated photovoltaic (BIPV) is one of the most holistic approaches to exploit it as a next-generation PV technology. Integration of high efficiency and semi-transparent PSC in BIPV is still not a well-established area. The purpose of this review is to get an overview of the relative scope of PSCs integration in the BIPV sector. This review demonstrates the benevolence of PSCs by stimulating energy conversion and its perspective and gradual evolution in terms of photovoltaic applications to address the challenge of increasing energy demand and their environmental impacts for BIPV adaptation. Understanding the critical impact regarding the materials and devices established portfolio for PSC integration BIPV are also discussed. In addition to highlighting the apparent advantages of using PSCs in terms of their demand, perspective and the limitations, challenges, new strategies of modification and relative scopes are also addressed in this review.

show abstract

Thermal and visual comfort analysis of adaptive vacuum integrated switchable suspended particle device window for temperate climate

Cited by 76 publications

References 81 publications

Status of BIPV and BAPV System for Less Energy-Hungry Building in India—A Review

Status of BIPV and BAPV System for Less Energy-Hungry Building in India—A Review

Visual Comfort Analysis of Semi-Transparent Perovskite Based Building Integrated Photovoltaic Window for Hot Desert Climate (Riyadh, Saudi Arabia)

Perovskite Solar Cells for BIPV Application: A Review

Contact Info

Product

Resources

About