Interfacial modification, which serves multiple roles, is vital for the fabrication of efficient and stable perovskite solar cells. Here, a multifunctional interfacial material, biguanide hydrochloride (BGCl), is introduced between tin oxide (SnO2) and perovskite to enhance electron extraction, as well as the crystal growth of the perovskite. The BGCl can chemically link to the SnO2 through Lewis coordination/electrostatic coupling and help to anchor the PbI2. Better energetic alignment, reduced interfacial defects, and homogeneous perovskite crystallites are achieved, yielding an impressive certified power conversion efficiency (PCE) of 24.4%, with an open‐circuit voltage of 1.19 V and a drastically improved fill factor of 82.4%. More importantly, the unencapsulated device maintains 95% of its initial PCE after aging for over 500 h at 20 °C and 30% relative humidity in ambient conditions. These results suggest that the incorporation of BGCl is a promising strategy to modify the interface and control the crystallization of the perovskite, toward the attainment of highly efficient and stable perovskite solar cells as well as other perovskite‐based electronics.

No abstract

Developing a high-performance donor polymer is critical for achieving efficient non-fullerene organic solar cells (OSCs). Currently, most high-efficiency OSCs are based on a donor polymer named PM6, unfortunately, whose performance is highly sensitive to its molecular weight and thus has significant batch-to-batch variations. Here we report a donor polymer (named PM1) based on a random ternary polymerization strategy that enables highly efficient non-fullerene OSCs with efficiencies reaching 17.6%. Importantly, the PM1 polymer exhibits excellent batch-to-batch reproducibility. By including 20% of a weak electron-withdrawing thiophene-thiazolothiazole (TTz) into the PM6 polymer backbone, the resulting polymer (PM1) can maintain the positive effects (such as downshifted energy level and reduced miscibility) while minimize the negative ones (including reduced temperature-dependent aggregation property). With higher performance and greater synthesis reproducibility, the PM1 polymer has the promise to become the work-horse material for the non-fullerene OSC community.

In this work, polymer solar cells are fabricated based on the blend of PTB7‐Th: PC71BM by using a mixed solvent additive of 1,8‐diiodooctane and N‐methyl pyrrolidone to optimize the morphology of the blend. A high power conversion efficiency (PCE) of 10.8% has been achieved with a simple conventional device. In order to deeply investigate the influence of the mixed solvent additives on the morphology and device performance, the variations of the molecular packing and bulk morphology of the blend film cast from ortho‐dichlorobenzene with single or binary solvent additives are measured. Although all the blend films exhibit similar domain size and nanoscale phase separation, the blend film processed with mixed solvent additive shows the highest domain purity, resulting in the least bimolecular recombination, relatively high Jsc and FF, and hence enhanced PCE. Therefore, the best photovoltaic performance with the Voc of 0.82 V, Jsc of 19.1 mA cm−2, FF of 69.1%, and PCE of 10.8% are obtained for the device based on the blend with binary solvent additive treatment.

In this work, a nonfullerene polymer solar cell (PSC) based on a wide bandgap polymer donor PM6 containing fluorinated thienyl benzodithiophene (BDT-2F) unit and a narrow bandgap small molecule acceptor 2,2'-((2Z,2'Z)-((4,4,9,9-tetrahexyl-4,9-dihydro-s-indaceno[1,2-b:5,6-b']dithiophene-2,7-diyl)bis(methanylylidene))bis(3-oxo-2,3-dihydro-1H-indene-2,1-diylidene))dimalononitrile (IDIC) is developed. In addition to matched energy levels and complementary absorption spectrum with IDIC, PM6 possesses high crystallinity and strong π-π stacking alignment, which are favorable to charge carrier transport and hence suppress recombination in devices. As a result, the PM6:IDIC-based PSCs without extra treatments show an outstanding power conversion efficiency (PCE) of 11.9%, which is the record value for the as-cast PSC devices reported in the literature to date. Moreover, the device performances are insensitive to the active layer thickness (≈95-255 nm) and device area (0.20-0.81 cm ) with PCEs of over 11%. Besides, the PM6:IDIC-based flexible PSCs with a large device area of 1.25 cm exhibit a high PCE of 6.54%. These results indicate that the PM6:IDIC blend is a promising candidate for future roll-to-roll mass manufacturing and practical application of highly efficient PSCs.