Recent technological advances in the field of additive manufacturing (AM), particularly with direct metal laser sintering (DMLS), have increased the potential for building gas turbine components with AM. Using the DMLS for turbine components broadens the design space and allows for increasingly small and complex geometries to be fabricated with little increase in time or cost. Challenges arise when attempting to evaluate the advantages of the DMLS for specific applications, particularly because of how little is known regarding the effects of surface roughness. This paper presents pressure drop and heat transfer results of flow through small, as produced channels that have been manufactured using the DMLS in an effort to better understand roughness. Ten different coupons made with the DMLS all having multiple rectangular channels were evaluated in this study. Measurements were collected at various flow conditions and reduced to a friction factor and a Nusselt number. Results showed significant augmentation of these parameters compared to smooth channels, particularly with the friction factor for minichannels with small hydraulic diameters. However, augmentation of Nusselt number did not increase proportionally with the augmentation of the friction factor.

Additive manufacturing (AM) with metal powder has made possible the fabrication of gas turbine components with small and complex flow paths that cannot be achieved with any other manufacturing technology presently available. The increased design space of AM allows turbine designers to develop advanced cooling schemes in high-temperature components to increase cooling efficiency. Inherent in AM with metals is the large surface roughness that cannot be removed from small internal geometries. Such roughness has been shown in previous studies to significantly augment pressure loss and heat transfer of small channels. However, the roughness on these channels or other surfaces made from AM with metal powder has not been thoroughly characterized for scaling pressure loss and heat transfer data. This study examines the roughness of the surfaces of channels of various hydraulic length scales made with direct metal laser sintering (DMLS). Statistical roughness parameters are presented along with other parameters that others have found to correlate with flow and heat transfer. The pressure loss and heat transfer previously reported for the DMLS channels studied in this work are compared to the physical roughness measurements. Results show that the relative arithmetic mean roughness correlates well with the relative equivalent sand grain roughness. A correlation is presented to predict the Nusselt number of flow through AM channels, which gives better predictions of heat transfer than correlations currently available.

Recent technological advances in the field of additive manufacturing (AM), particularly with direct metal laser sintering (DMLS), have increased the potential for building gas turbine components with AM. Using DMLS for turbine components broadens the design space and allows for increasingly small and complex geometries to be fabricated with little increase in time or cost. Challenges arise when attempting to evaluate the advantages of DMLS for specific applications, particularly because of how little is known regarding the effects of surface roughness. This paper presents pressure drop and heat transfer results of flow through small, as produced channels that have been manufactured using DMLS in an effort to better understand roughness. Ten different coupons made with DMLS all having multiple rectangular channels were evaluated in this study. Measurements were collected at various flow conditions and reduced to a friction factor and a Nusselt number. Results showed significant augmentation of these parameters compared to smooth channels, particularly with the friction factor for mini-channels with small hydraulic diameters. However, augmentation of Nusselt number did not increase proportionally with the augmentation of the friction factor.

With the advance of direct metal laser sintering (DMLS), also generically referred to as additive manufacturing (AM), novel geometric features of internal channels for gas turbine cooling can be achieved beyond those features using traditional manufacturing techniques. There are many variables, however, in the DMLS process that affect the final quality of the part. Of most interest to gas turbine heat transfer designers are the roughness levels and tolerance levels that can be held for the internal channels. This study investigates the effect of DMLS build direction and channel shape on the pressure loss and heat transfer measurements of small-scale channels. Results indicate that differences in pressure loss occur between the test cases with differing channel shapes and build directions, while little change is measured in heat transfer performance.

With the advances of Direct Metal Laser Sintering (DMLS), also generically referred to as additive manufacturing, novel geometric features of internal channels for gas turbine cooling can be achieved beyond those features using traditional manufacturing techniques. There are many variables, however, in the DMLS process that affect the final quality of the part. Of most interest to gas turbine heat transfer designers are the roughness levels and tolerance levels that can be held for the internal channels. This study investigates the effect of DMLS build direction and channel shape on the pressure loss and heat transfer measurements of small scale channels. Results indicate that differences in pressure loss occur between the test cases with differing channel shapes and build directions, while little change is measured in heat transfer performance.