Summary. The aim of this study was to investigate antiradical activity of aqueous and ethanolic hawthorn fruit extracts, their flavonoids, and flavonoid combinations.Material and methods. Total amount of phenolic compounds and the constituents of flavonoids were determined using a high-performance liquid chromatography. The antioxidant activity of Crataegus monogyna extracts and flavonoids (chlorogenic acid, hyperoside, rutin, quercetin, vitexin-2O-rhamnoside, epicatechin, catechin, and procyanidin B 2 ) quantitatively was determined using the method of spectrophotometry Medicina (Kaunas) 2008; 44(9)

The main objective of this study was to evaluate the influence of the formulation and process parameters on PLGA microparticles containing a practically insoluble model drug (ibuprofen) prepared by the o/w solvent evaporation method. Multivariate data analysis was used. The effects of altered stirring speed of a mechanical stirrer (600, 1000 rpm), emulsifier concentrations (PVA concentration 0.1 %, 1 %) and solvent selection (dichloromethane, ethyl acetate) on microparticle characteristics (encapsulation efficiency, drug loading, burst effect) were observed. It was found that with increased stirring speed, the PVA concentration or the use of ethyl acetate had a significantly negative effect on encapsulation efficiency. In addition, ethyl acetate had an adverse effect on the burst effect, while increased stirring speed had the opposite effect. Drug load was not affected by any particular variable, but rather by the interactions of evaluated variables.

No abstract

The aim of the study was to prepare pellets of maidenhair tree (Ginkgo biloba), motherwort (Leonurus cardiaca) and hawthorn (Crataegus monogyna) dry extracts by extrusion/spheronization method. The critical step of this process was the amount of added wetting liquid (water-ethanolic mixture) and the amount of extract in the formulation. The samples of pellets containing 30-50% of extracts were formulated: Pellets contained extracts of Ginkgo, Crataegi and Leonuri. The last sample was aimed at the formulation of pellets with the content of 30% of the mixture of Ginkgo, Leonuri and Crataegi extracts in a ratio of 1:5:6. The remainder of the solid compounds in all formulations was microcrystalline cellulose (Avicel® PH-101). It was not possible to find a way to adequately wet the formulations with the content of extracts higher than 30% because of the unsuitable properties of all three extracts used. On the basis of the experiments, pellets with mixtures of all three previously used extracts were prepared. These pellets showed perfect physico-mechanical properties: Hardness (10.00 ± 2.24 N), friability (0.06%), repose angle (20.99 ± 0.41°), flowability (6.97 ± 0.29 s/100g of pellets), sphericity (0.81 ± 0.05), compressibility index (4.65%), intraparticular porosity (0.09%) and interparticular porosity (45.11%), which predetermine them to other testing and usage (feeling into capsules, tableting, coating etc.).

Oral mucosa is an attractive region for the local and systemic application of many drugs. Oral mucoadhesive films are preferred for their prolonged time of residence, the improved bioavailability of the drug they contain, their painless application, their protection against lesions, and their nonirritating properties. This work was focused on preparation of nonmedicated carmellose-based films using both solvent casting and impregnation methods, respectively. Moreover, a modern approach to evaluation of mucoadhesive films applying analysis of texture and subsequent multivariate data analysis was used. In this experiment, puncture strength strongly correlated with tensile strength and could be used to obtain necessary information about the mechanical film characteristics in films prepared using both methods. Puncture work and tensile work were not correlated in films prepared using the solvent casting method, as increasing the amount of glycerol led to an increase in the puncture work in thinner films. All measured texture parameters in films prepared by impregnation were significantly smaller compared to films prepared by solvent casting. Moreover, a relationship between the amount of glycerol and film thickness was observed, and a greater recalculated tensile/puncture strength was needed for an increased thickness in films prepared by impregnation.