A drilling fluid for drilling deviated wellbores must provide adequate hole cleaning efficiency for all well angles relevant to the operation. For angles near vertical, experience show that hole cleaning is straight forward. In wellbore angles larger than, say, 45 degrees hole cleaning is more difficult. Cuttings beds are formed and at some well angles these beds may avalanche during circulation stops etc. This paper presents results from laboratory tests with injected cuttings using a low viscosity oil based drilling fluid with micronized grained barite as weight material. The fluid is designed for highly deviated wells with low ECD requirements and the cuttings transport performance through relevant wellbore inclinations was investigated. The experiments have been performed under realistic conditions. The flow loop includes a 10 meters long test section with 2” OD freely rotating steel drill string inside a 4” ID wellbore made of steel, representing a cased wellbore. Sand particles were injected while circulating the drilling fluid through the test section. Experiments were performed in three wellbore inclinations: 48, 60 and 90 degrees from vertical. Results show that hole cleaning in absence of drill pipe rotation is significantly improved if the well angle is less than a critical angle. This critical angle appears to be less than 60 degrees from vertical. Further result show that this critical inclination angle is dependent to the drill string rotation rate and the annular flow velocity.

In this paper, we present results from flow loop experiments with an oil-based drilling fluid with micronized barite as weight materials. The use of micronized barite allows using lower viscosity drilling fluid, providing non-laminar flow, which is advantageous for particle transport in near-horizontal sections. While transition to turbulence and turbulent flow of non-Newtonian fluids has been well studied both theoretically and experimentally, there are very few published results on the effect of wellbore wall properties on flow regime transition and turbulence. This is relevant because horizontal sections are often open hole with less well-defined surfaces than a steel casing surface. We have conducted a series of flow experiments with and without cuttings size particles in a 10 m long annular test section using steel and concrete material to represent the wellbore wall of a cased and open hole section. In both cases the annulus was formed by a freely rotating steel pipe of 2" outer diameter inside a 4" diameter wellbore. Experiments were conducted at 48°, 60° and 90° wellbore inclination from vertical. The two materials result in different hydraulic behavior without particles with stronger turbulence when using concrete wellbore wall material than when using steel casing. While there is negligible difference at low flow rates, at 0.8 m/s and below, there is an increasing difference as the flow rate increases and becomes transitional to turbulence. Hole cleaning is found to differ dependent on the wall material. However, the effect on hole cleaning is less clear than for the pressure loss.

Results from cuttings transport tests in laboratory using different field applied oil-based drilling fluids with similar weight and varying viscosities are presented in this paper. The fluids are designed for highly deviated wells, and the cuttings transport performance at relevant wellbore inclinations was investigated. The experiments have been performed in a flow loop that consists of a 10 meters long test section with 50.4 mm (2″) diameter freely rotating steel drill string inside a 100 mm (≈4″) diameter wellbore made of cement. Sand particles were injected while circulating the drilling fluid through the test section. Experiments were performed at three wellbore inclinations: 48, 60 and 90 degrees from vertical. The applied flow loop dimensions are designed so that the results are scalable to field applications; especially for the 12 ¼” and 8 ½″ sections. The selected setup provides correct shear rate ranges and similar Reynolds numbers to the field application when the same fluids are applied. Results show that hole cleaning abilities of the tested fluids vary significantly with well angle, drill string rotation and flow rate. Results support field experience showing that low viscous fluids are more efficient than viscous fluids at higher flow rates and low drill string rotation. As well as per field experience more viscous fluids are efficient in combination with high drill string rotation rates. The results show the effect of cuttings transport efficiency as function of hydraulic frictional pressure drop, demonstrating methods to achieve more optimal hydraulic design in the tested conditions. The key findings have direct relevance to drilling operations.

Drilling fluids are very complex and are essential for safe and efficient drilling operations. It is vital for the drilling operator to be able to select an appropriate fluid for each individual well, including the decision of using oil-based or water-based fluids or “muds” (OBM or WBM). In this article we present results from a comparative study of three OBM’s which are based on the same fluid system (Versatec). This work is part of a larger investigation where the main objective is to identify and evaluate the difference in the hole cleaning capabilities of OBM’s and WBM’s with similar viscosity as measured by the API/ISO standards. This paper describes an experimental investigation of cuttings transport using flow loop laboratory tests without and with injected cuttings size particles using various industrial oil based fluids with varying density and viscosity. The flow loop includes a 10 meter long test section with 2″ OD free whirling rotating steel drillstring inside a 4″ ID wellbore made of concrete elements positioned inside a steel tubing. Sand particles were injected while circulating the drilling fluid through the test section. Experiments are conducted at atmospheric conditions, but are otherwise designed to represent downhole conditions as closely as possible with respect to fluid and particle properties, flow rates and geometry. Fluids are tested at different flow rates with and without rotation of drill string, with and without sand injection. This has allowed us to study the effects of flow rate and drill string rotation on hole cleaning capabilities of different fluids. The primary results are pressure drop, steady state sand bed height in a horizontal annulus versus fluid and cuttings rates for rotating and non-rotating drill string and in particular the critical rates for fully suspended flow. The results are interpreted in light of results from laboratory characterization of the same fluids, conducted as part of the same project. The results will increase understanding of the relationship between drilling fluid properties and hole cleaning performance. This will enable the development of improved drilling fluids, both operationally and environmentally. Such know-how will also be important in order to develop more accurate transport models.