The continuous growth of the concrete industry requires an increased quantity of cement and natural aggregates year after year, and it is responsible for a major part of the global CO2 emissions. These aspects led to rigorous research for suitable raw materials. Taking into account that these raw materials must have a sustainable character and also a low impact on environmental pollution, the replacement of the conventional components of concrete by residual waste can lead to these targets. This paper’s aim is to analyze the density, compressive strength and the thermal conductivity of nine concrete compositions with various rates of waste: four mixes with 10%, 20%, 40% and 60% chopped PET bottles aggregates and 10% fly ash as cement partial substitution; a mix with 60% waste polystyrene of 4–8 mm and 10% fly ash; a mix with 20% waste polystyrene of 4–8 mm, 10% waste polystyrene of 0–4 mm and 10% fly ash; a mix with 50% waste polystyrene of 4–8 mm, 20% waste polystyrene of 0–4 mm and 20% fly ash two mixes with 10% fly ash and 10% and 40% waste sawdust, respectively. Using 60% PET aggregates, 60% polystyrene granules of 4–8 mm, or 20% polystyrene of 0–4 mm together with 50% polystyrene of 4–8 mm led to the obtainment of lightweight concrete, with a density lower than 2000 kg/m3. These mixes also registered the best results from a thermal conductivity point of view, after the concrete mix with 40% saw dust. Regarding compressive strength, the mix with 10% PET obtained a result very close to the reference mix, while those with 20% PET, 40% PET, 30% polystyrene, and 10% saw dust, respectively, registered values between 22 MPa and 25 MPa, values appropriate for structural uses.

Based on the monitoring campaigns, we have evaluated the indoor microclimate in a church. Most church buildings are characterised by low thermal comfort due primarily to their architecture, heating huge volume of air. The CFD tools was used for thermal comfort evaluation in case of the existing heating system during the winter season. The simulation model was validated with experimental data and it was used for thermal and air velocity profiles in the occupancy zone of churchgoers. The aim of the paper is the study the feasibility of maintaining the heritage values of the churches while achieving the significant improvement of the thermal comfort.

One of the biggest challenges the world is facing these days is to reduce the greenhouse gases emissions in order to prevent the global warming. Since a significant quantity of CO2 emissions is the result of the energy producing process required in industry or buildings, the waste heat recovery is an important aspect in the fight for preserving the planet. In this study, an innovative waste heat recovery system which can recover waste heat energy from cooling liquids used in industry or in different processes, was designed and subjected to experimental investigations. The equipment uses heat pipes to capture thermal energy from the residual fluids transiting the evaporator zone and transfer it to the cold water transiting the condenser zone. The efficiency of the heat exchanger was tested in 9 scenarios, by varying the temperature of the primary agent to 60, 65 and 70 °C and the volume flow rate of the secondary agent to 1, 2 and 3 L/min. The temperature of the secondary agent and the volume flow rate of the primary agent were kept constant at 10 °C, respectively 24 L/min. The results were later validated through numerical simulations, and confirmed that the equipment can easily recover waste thermal energy from used water with low and medium temperatures at very low costs compared to the traditional heat exchangers. The results were promising, revealing an efficiency of the equipment up to 76.7%.

The paper presents a numerical analysis of the operation of photovoltaic (PV) panels integrated in fixed position on the roofs or facades of the buildings. Knowing that the efficiency of photovoltaic panels is temperature-dependent, and due to fixed PV panel position, the possibility of the improving the conversion is analysed from the point of view of the temperature of the PV cells. The model is simulated using TRNSYS software and the main functioning parameters assessed are the operating temperature of the cells, open circuit voltage, maximum power generated and conversion efficiency. The solution proposed for cooling consists in using water heat exchangers attached to the backside of the photovoltaic panel. The results highlight the direct dependence of the photovoltaic efficiency with the temperature of the panel for different positions in the same geographical location. The energy gain during the cooling interval is about 26.9 Wh/m2 (vertical), 81.9 Wh/m2 (inclined) and 81.7 Wh/m2 (horizontal), which represents an increase of 5.8%, 9.3% and 9.2% respectively, compared to the normal operating conditions.

This paper presents the simulation method for evaluating the heating system from a church. The inside climate has been evaluated by measures of temperature and humidity taken in the winter season. The aim of the paper is to model and validate the indoor climate measures thought numerical analysis and to evaluate the heating system performance. The paper include a case study over and representative category of buildings, used as worship place that can contain heritage values. Nowadays, to conserve the historical heritage is a fact studied in many countries of Europe.