A scanning tunneling microscope operated under ambient conditions was utilized to study the self-assembly of trimesic acid (TMA) at the liquid-solid interface. On a graphite substrate, two different open, loosely packed, two-dimensional hydrogen-bond networks were found. Both structures exhibit a periodic arrangement of approximately 1.0 nm wide cavities, which can be used for the co-adsorption of another species (guest) within the cells of this host system. These two polymorphs ("chickenwire" and "flower" structures) differ in their molecular packing density and hydrogen-bonding schemes. Using a homologous series of alkanoic acids as solvents, ranging from butyric to nonanoic, selective self-assembly of either the "flower" or "chickenwire" forms was achieved on a graphite surface. Solubility of TMA in these acid solvents was found to decrease with increasing chain length, and the longer-chain solvents favored formation of the chickenwire polymorph structure on the surface.

The adsorption of 1,3,5-Benzenetricarboxylic (Trimesic) Acid (TMA) to a single crystal graphite surface has been studied under Ultra High Vacuum conditions. This work focuses on inducing a particular self-assembly structure by OMBE (Organic Molecular Beam Epitaxy), characterized by periodic non-dense-packing of the molecules. Two coexisting phases could be imaged with sub-molecular resolution by STM. Induced by directed hydrogen bonding, the organic molecules built in both cases a two-dimensional grid architecture with molecular caves. This two-dimensional host structure can accept single trimesic acid guest molecules in different positions.

In this work, the thermoelectric (TE) properties of poly(3,4- ethylenedioxylthiophene):poly(styrene sulfonate) (PEDOT:PSS) thin films at room temperature are studied. Different methods have been applied for tuning the TE properties: 1st addition of polar solvent, dimethyl sulfoxide (DMSO), into the PEDOT:PSS solution; 2nd post-treatment of thin films with a mixture of DMSO and ionic liquid, 1-ethyl-3-methylimidazolium tetrafluoroborate (EMIMBF4). It is verified that DMSO post-treatment is more efficient than DMSO addition in improving the electrical conductivity with a trivial change in the Seebeck coefficient. The power factor is increased up to 30.1 W mK-2 for the film with DMSO post-treatment, while the optimized power factor by DMSO addition is 18.2 W mK-2. It is shown that both DMSO addition and post-treatment induce morphological changes: an interconnected network of elongated PEDOT grains is generated, leading to higher electrical conductivity. In contrast, for t hose films post-treated in the presence of EMIMBF4, an interconnected network of short and circular PEDOT grains with increased polaron density is created, resulting in the improvement in the Seebeck coefficient and a concomitant compromise in the electrical conductivity. An optimized power factor of 38.46 W mK -2 is achieved at 50 vol% of EMIMBF4, which is the highest reported so far for PEDOT:PSS thin films to our knowledge. Assuming a thermal conductivity of 0.17 W mK-1, the corresponding ZT is 0.068 at 300 K. These results demonstrate that post-treatment is a promising approach to enhance the TE properties of PEDOT:PSS thin films. Furthermore, ionic liquid, EMIMBF4, shows the potential for tuning the TE properties of PEDOT:PSS thin films via a more environmentally benign process

A two-dimensional molecular template structure of 1,3,5-benzenetricarboxylic acid (trimesic acid, TMA) was formed on a highly oriented pyrolytic graphite surface (HOPG) by self-assembly at the liquid-solid interface. Scanning tunneling microscopy (STM) investigations show high-resolution images of the porous structure on the surface. After the host structure was created, coronene molecules were inserted as guest molecules into the pores. STM results indicate that some of the guest molecules rotate inside their molecular bearing. Further investigations show that single coronene molecules can be directly kicked out of their pores by means of STM.