A novel small molecule, FBR, bearing 3-ethylrhodanine flanking groups was synthesized as a nonfullerene electron acceptor for solution-processed bulk heterojunction organic photovoltaics (OPV). A straightforward synthesis route was employed, offering the potential for large scale preparation of this material. Inverted OPV devices employing poly(3-hexylthiophene) (P3HT) as the donor polymer and FBR as the acceptor gave power conversion efficiencies (PCE) up to 4.1%. Transient and steady state optical spectroscopies indicated efficient, ultrafast charge generation and efficient photocurrent generation from both donor and acceptor. Ultrafast transient absorption spectroscopy was used to investigate polaron generation efficiency as well as recombination dynamics. It was determined that the P3HT:FBR blend is highly intermixed, leading to increased charge generation relative to comparative devices with P3HT:PC60BM, but also faster recombination due to a nonideal morphology in which, in contrast to P3HT:PC60BM devices, the acceptor does not aggregate enough to create appropriate percolation pathways that prevent fast nongeminate recombination. Despite this nonoptimal morphology the P3HT:FBR devices exhibit better performance than P3HT:PC60BM devices, used as control, demonstrating that this acceptor shows great promise for further optimization.

The design, synthesis, and characterization of a series of diketopyrrolopyrrole-based copolymers with different chalcogenophene comonomers (thiophene, selenophene, and tellurophene) for use in field-effect transistors and organic photovoltaic devices are reported. The effect of the heteroatom substitution on the optical, electrochemical, and photovoltaic properties and charge carrier mobilities of these polymers is discussed. The results indicate that by increasing the size of the chalcogen atom (S < Se < Te), polymer band gaps are narrowed mainly due to LUMO energy level stabilization. In addition, the larger heteroatomic size also increases intermolecular heteroatom-heteroatom interactions facilitating the formation of polymer aggregates leading to enhanced field-effect mobilities of 1.6 cm(2)/(V s). Bulk heterojunction solar cells based on the chalcogenophene polymer series blended with fullerene derivatives show good photovoltaic properties, with power conversion efficiencies ranging from 7.1-8.8%. A high photoresponse in the near-infrared (NIR) region with excellent photocurrents above 20 mA cm(-2) was achieved for all polymers, making these highly efficient low band gap polymers promising candidates for use in tandem solar cells.

Conjugated polymers that support mixed (electronic and ionic) conduction are in demand for applications spanning from bioelectronics to energy harvesting and storage. To design polymer mixed conductors for high‐performance electrochemical devices, relationships between the chemical structure, charge transport, and morphology must be established. A polymer series bearing the same p‐type conjugated backbone with increasing percentage of hydrophilic, ethylene glycol side chains is synthesized, and their performance in aqueous electrolyte gated organic electrochemical transistors (OECTs) is studied. By using device physics principles and electrochemical analyses, a direct relationship is found between the OECT performance and the balanced mixed conduction. While hydrophilic side chains are required to facilitate ion transport—thus enabling OECT operation—swelling of the polymer is not de facto beneficial for balancing mixed conduction. It is shown that heterogeneous water uptake disrupts the electronic conductivity of the film, leading to OECTs with lower transconductance and slower response times. The combination of in situ electrochemical and structural techniques shown here contributes to the establishment of the structure–property relations necessary to improve the performance of polymer mixed conductors and subsequently of OECTs.

for this application. [1][2][3][4][5][6] Recently, however, new classes of materials are being investigated for hydrogen evolution from water, such as nitrogen doped graphene oxide, [7] covalent organic frameworks, [8][9][10] conjugated polymer networks, [11][12][13][14] and linear conjugated polymers. [15][16][17][18][19][20] With the notable exception of graphitic carbon nitride, [21] most organic semiconductors have required an additional metal co-catalyst to produce an appreciable H 2 evolution rate, often introduced by Pt photo deposition, [22] or the addition of a molecular catalyst. [8,23,24] However, recent reports of photocatalysis employing both linear and cross-linked conjugated polymers suggest that these systems are able to produce H 2 under visible light irradiation without any added co-catalyst, at a much faster rate than commercial graphitic carbon nitride, even when the latter is subjected to Pt photodeposition. [11] Activity without the need for co-catalysts, which are often precious metals or molecular complexes with limited stability, [25] could be a very attractive feature of such polymer photocatalysts with the potential to vastly reduce the cost and complexity of current photocatalytic systems.A feature of these linear and cross-linked conjugated polymers that has not yet been systematically studied is the presence of significant quantities of residual Pd originating from their synthesis via Pd catalyzed polycondensation reactions. [11,12,15,26] It has previously been shown that the molecular Pd catalysts used in these reactions can decompose via deligation and subsequent Ostwald ripening to form metallic Pd 0 particles, which are strongly retained within the polymer matrix and are difficult to remove via classical purification techniques. [27][28][29][30][31] Similar to Pt 0 , Pd 0 is a highly active proton reduction electrocatalyst. [32][33][34] Therefore, it is possible that the residual Pd, dispersed within these polymer structures, facilitates H 2 evolution and removes the need for additional co-catalysts. Much uncertainty remains about the nature of the active site in conjugated polymer systems, and there are conflicting views in the literature on whether or not the residual amounts of Pd play a significant role. No correlation was seen between Pd concentration and hydrogen evolution reaction (HER) rate in a range of conjugated micro porous polymers, [11] and in a series of linear polymersThe effect of residual Pd on hydrogen evolution activity in conjugated polymer photocatalytic systems is systematically investigated using colloidal poly(9,9-dioctylfluorene-alt-benzothiadiazole) (F8BT) nanoparticles as a model system. Residual Pd, originating from the synthesis of F8BT via Pd catalyzed polycondensation polymerization, is observed in the form of homogeneously distributed Pd nanoparticles within the polymer. Residual Pd is essential for any hydrogen evolution to be observed from this polymer, and very low Pd concentrations (<40 ppm) are sufficient to have a significant effect on the h...