The authors have been developing a newly-designed totally-implantable artificial myocardium using a covalent shape-memory alloy fibre (Biometal®, Toki Corporation), which is attached onto the ventricular wall and is also capable of supporting the natural ventricular contraction. This mechanical system consists of a contraction assistive device, which is made of Ti-Ni alloy. And the phenomenon of the martensitic transformation of the alloy was employed to achieve the physiologic motion of the device. The diameter of the alloy wire could be selected from 45 to 250μm. In this study, the basic characteristics of the fiber of 150μm was examined to design the sophisticated mechano-electric myocardium. The stress generated by the fiber was 400gf under the pulsatile driving condition (0.4W, 1Hz). Therefore it was indicated that the effective assistance might be achieved by using the Biometal shape-memory alloy fiber.

The authors have been developing a mechano-electric artificial myocardial assist system (artificial myocardium) which is capable of supporting natural contractile functions from the outside of the ventricle without blood contacting surface. In this study, a nano-tech covalent type shape memory alloy fibre (Biometal, Toki Corp, Japan) was employed and the parallel-link structured myocardial assist device was developed. And basic characteristics of the system were examined in a mechanical circulatory system as well as in animal experiments using goats. The contractile functions were evaluated with the mock circulatory system that simulated systemic circulation with a silicone left ventricular model and an aortic afterload. Hemodynamic performance was also examined in goats. Prior to the measurement, the artificial myocardial assist device was installed into the goat's thoracic cavity and attached onto the ventricular wall. As a result, the system could be installed successfully without severe complications related to the heating, and the aortic flow rate was increased by 15% and the systolic left ventricular pressure was elevated by 7% under the cardiac output condition of 3L/min in a goat. And those values were elevated by the improvement of the design which was capable of the natural morphological myocardial tissue streamlines. Therefore it was indicated that the effective assistance might be achieved by the contraction by the newly-designed artificial myocardial assist system using Biometal. Moreover it was suggested that the assistance gain might be obtained by the optimised configuration design along with the natural anatomical myocardial stream line.

This paper studies the structural design of the wireless-electrodeless quartz crystal microbalance (QCM) sensor, which has a rectangular AT-cut quartz oscillator installed in the microchannel fabricated by nanoimprint lithography. The quartz oscillator was supported by the micropillars in the microchannel, and by optimizing the micropillar arrangement, it was found that the structural damping could be significantly reduced by performing the finite elemental piezoelectric analysis. This behavior was then confirmed by the experiments using the evaluation chips. By supporting the four corners of the quartz oscillator with the micropillars, the structural damping could be reduced, achieving a high-quality factor (Q-factor) of about 24700. This high Q-factor was also realized in the experiments, and we investigated its application to a hydrogen-gas sensor. We succeeded in detecting hydrogen gas with an extremely low concentration of 10 ppm.

The authors have been developing an artificial myocardium, which is capable of supporting natural contractile function from the outside of the ventricle. The system was originally designed by using sophisticated covalent shape memory alloy fibres, and the surface did not implicate blood compatibility. The purpose of our study on the development of artificial myocardium was to achieve the assistance of myocardial functional reproduction by the integrative small mechanical elements without sensors, so that the effective circulatory support could be accomplished. In this study, the authors fabricated the prototype artificial myocardial assist unit composed of the sophisticated shape memory alloy fibre (Biometal), the diameter of which was 100 microns, and examined the mechanical response by using pulse width modulation (PWM) control method in each unit. Prior to the evaluation of dynamic characteristics, the relationship between strain and electric resistance and also the initial response of each unit were obtained. The component for the PWM control was designed in order to regulate the myocardial contractile function, which consisted of an originally-designed RISC microcomputer with the input of displacement, and its output signal was controlled by pulse wave modulation method. As a result, the optimal PWM parameters were confirmed and the fibrous displacement was successfully regulated under the different heat transfer conditions simulating internal body temperature as well as bias tensile loading. Then it was indicated that this control theory might be applied for more sophisticated ventricular passive or active restraint by the artificial myocardium on physiological demand.

The hydrogen energy, which is environmentally friendly and does not emit carbon dioxide, has been attracting attention as an alternative fuel to the fossil fuel. In the shift to a hydrogen energy society, the highly sensitive hydrogen gas sensor has been required for the storage and management of hydrogen gas. In this research, we propose a film deposition method to induce the in-plane plastic deformation in the thin film, and apply it to a hydrogen gas sensor, where the palladium film formed by this method is deposited on a thin quartz resonator. It is found that the sensor chip with the plastically deformed palladium film is about 1.5 times more sensitive than the conventional sensor chip and has high-speed response. The developed sensor is a novel device that can be used in an oxygen-free environment without any temperature compensation and constant heating.