A d.c. oxygen glow discharge was used to modify medical-grade poly(vinyl chloride) (PVC) to study how surface chemistry and hydrophilicity influence Pseudomonas aeruginosa adhesion. The effects of plasma exposure time on the resulting surface, including chemical composition, wettability and roughness, were assessed using x-ray photoelectron spectroscopy, contact angle measurements and atomic force microscopy analysis. A significant alteration in the hydrophilicity of the native PVC surface was observed after oxygen glow discharge treatment. The water contact angle decreased from ∼80• to 8-20• , with a weak dependence of the exposure time used. The change in surface wettability resulted from the incorporation of oxygenated functional groups, including esters, ketones and acids, as indicated by XPS analysis. The amount of oxygen incorporation was shown to be essentially independent of plasma exposure time. However, prolonged plasma exposure resulted in increased surface roughness. Bacterial adhesion efficiency was evaluated for PVC modified by 120 s of plasma exposure, because this exposure time was determined to yield the maximum decrease in contact angle. Oxygen plasma treatment of native PVC was found to yield a 70% reduction in bacterial adhesion for the four strains of Pseudomonas aeruginosa tested.

We present an investigation of the physico-chemical surface properties of commercially pure titanium coverslips which were submitted to various treatments designed to optimize their topography in view of application in oral implantology. The surface microroughness, chemical composition and water wettability were analyzed on titanium coverslips prepared by mechanical polishing, acid attack in HCl/H2SO4, after mechanical polishing or sandblasting, and titanium plasma-spray. The chemical composition has been measured by Auger electron spectroscopy. The treatments have no major influence on the surface chemical composition and all the samples display a composition approaching that of TiO2 with minor amounts of carbon, sulfur, silicon and calcium as impurities. The roughness has been measured by scanning force microscopy on an area of 20 microns x 20 microns on each sample. Polished titanium is smooth (peak-to-valley roughness 81 nm), whereas the acid-attacked surfaces exhibit a micro-roughness in the microns range (2100 nm for polished and acid attacked; 3600 nm for sandblasted and acid attacked) which is quite reproducible over large areas of the sample. The acid attacked samples present a subsurface layer which contains hydrogen below the native passivating oxide layer. Water wettability measurement shows that all surfaces are hydrophobic with a slightly higher contact angle for the acid attacked surfaces. The different treatments analyzed in this study essentially influence the surface roughness by preserving the chemical composition and the wettability properties of titanium native oxide surface layer.

No abstract

Diamond-like carbon (DLC) and silicon carbide (SiC) coatings are attractive because of low friction coefficient, high hardness, chemical inertness and smooth finish, which they provide to biomedical devices. Silicon wafers (Si waf ) and silicone rubber (Si rub ) plates were coated using plasmaenhanced chemical vapour deposition (PE-CVD) techniques. This article describes: 1-the characterization of modified surfaces using attenuated total reflection-Fourier transform infrared spectroscopy (ATR/FTIR) and contact angle measurements, 2-the results of three in-vitro haemocompatibility assays. Coated surfaces were compared to uncoated materials and various substrates such as polymethylmethacrylate (PMMA), polyethylene (LDPE), polydimethylsiloxane (PDMS) and medical steel (MS). Thrombin generation, blood platelet adhesion and complement convertase activity tests revealed the following classification, from the most to the least heamocompatible surface: Si rub / DLC-Si rub / DLC-Si waf / LDPE/ PDMS/ SiCSi waf / Si waf / PMMA/ MS. The DLC coating surfaces delayed the clotting time, tended to inhibit the platelet and complement convertase activation, whereas SiC-coated silicon wafer can be considered as thrombogenic. This study has taken into account three events of the blood activation: coagulation, platelet activation and inflammation. The response to those events is an indicator of the in vitro haemocompatibility of the different surfaces and it allows us to select biomaterials for further in vivo blood contacting investigations.

Titanium is widely used in dental implants due to its suitable physical properties and its good biocompatibility. However, it is integrated into bone only passively, and the resulting fixation in the bone, which is necessary for the function, is mainly mechanical in nature. With the objective of increasing the chemical interaction between the implant and the bone tissue, several phosphonic acids were synthesized and grafted onto titanium disks. Here we report on the proliferation, differentiation, and protein production of rat osteoblastic cells (CRP10/30) on phosphonic-acid-modified titanium surfaces studied in vitro. No statistical differences were found in osteoblast proliferation among the phosphonic-acid-modified titanium, unmodified titanium, and tissue culture plastic (used as a positive control), indicating that the phosphonic acids used were not cytotoxic to the osteoblasts used. For all surfaces (modified or not), the alkaline phosphatase activity was at least as good as it was on tissue culture plastic. However, the total amount of protein, and especially the collagen type I synthesis, was sensitive to surface modification. On titanium modified with ethane-1,1,2-triphosphonic acid, the total amount of synthesized protein was significantly higher than it was on unmodified titanium surfaces. A significant increase (up to 16%) of collagen type I production was observed on titanium surfaces modified with this acid or with methylenediphosphonic acid compared to unmodified titanium surfaces.