The present study investigated the strain response of a distributed optical fiber sensor (DOFS) sealed in a groove at the surface of a concrete structure using a polymer adhesive and aimed to identify optimal conditions for crack monitoring. A finite element model (FEM) was first proposed to describe the strain transfer process between the host structure and the DOFS core, highlighting the influence of the adhesive stiffness. In a second part, mechanical tests were conducted on concrete specimens instrumented with DOFS bonded/sealed using several adhesives exhibiting a broad stiffness range. Distributed strain profiles were then collected with an interrogation unit based on Rayleigh backscattering. These experiments showed that strain measurements provided by DOFS were consistent with those from conventional sensors and confirmed that bonding DOFS to the concrete structure using soft adhesives allowed to mitigate the amplitude of local strain peaks induced by crack openings, which may prevent the sensor from early breakage. Finally, the FEM was generalized to describe the strain response of bonded DOFS in the presence of crack and an analytical expression relating DOFS peak strain to the crack opening was proposed, which is valid in the domain of elastic behavior of materials and interfaces.

The present study investigates the environmental durability of a distributed optical fiber sensing (DOFS) cable on the market, commonly used for distributed strain measurements in reinforced concrete structures. An extensive experimental program was conducted on different types of specimens (including samples of bare DOFS cable and plain concrete specimens instrumented with this DOFS cable) that were exposed to accelerated and natural ageing (NA) conditions for different periods of up to 18 months. The instrumentation of both concrete specimens consisted of DOFS cables embedded at the center of the specimens and bonded at the concrete surface, as these two configurations are commonly deployed in the field. In these configurations, the alkalinity of the surrounding cement medium and the outdoor conditions are the main factors potentially affecting the characteristics of the DOFS component materials and the integrity of the various interfaces, and hence impacting the strain transfer process between the host structure and the core optical fiber (OF). Therefore, immersion in an alkaline solution at an elevated temperature or freeze/thaw (F/T) and immersion/drying (I/D) cycles were chosen as accelerated ageing conditions, depending on the considered configuration. Mechanical characterizations by tensile and pull-out tests were then carried out on the exposed specimens to assess the evolution of the mechanical properties of individual component materials as well as the evolution of bond properties at various interfaces (internal interfaces of the DOFS cable, and interface between the cable and the host structure) during ageing. Complementary physico-chemical characterizations were also performed to better understand the underlying degradation processes. The experimental results highlight that immersion in the alkaline solution induced a significant and rapid decrease in the bond properties at internal interfaces of the DOFS cable and at the cable/concrete interface (in the case of the embedded cable configuration), which was assigned to chemical degradation at the surface of the cable coating in contact with the solution (hydrolysis and thermal degradation of the EVA copolymer component). Meanwhile, F/T and I/D cycles showed more limited effects on the mechanical properties of the component materials and interfaces in the case of the bonded cable configuration. A comparison with the same specimens exposed to outdoor NA suggested that the chosen accelerated ageing conditions may not be totally representative of actual service conditions, but provided indications for improving the ageing protocols in future research. In the last part, an analysis of the distributed strain profiles collected during pull-out tests on instrumented concrete specimens clearly illustrated the consequences of ageing processes on the strain response of the DOFS cable.

The CABRI International Program (CIP) tests irradiated UO2 or MOX fuels submitted to Reactivity Initiated Accidents (RIA) representative power pulses in prototypical PWR thermal-hydraulic conditions. CIP is managed by The Institut de Radioprotection et de Sûreté Nucléaire (IRSN) within a OECD/NEA framework. Experiments are conducted in the CABRI reactor operated by CEA. For CIP, CABRI benefits from a new pressurized water loop. An important refurbishment program enhanced the facility safety and upgraded the experimental equipment such as the nondestructive examination bench IRIS and the Hodoscope on-line fuel motion monitoring system. Specific test devices with appropriate innovative instrumentation follow the test rod behavior during the transient.The successful first test in the pressurized water loop demonstrated the CABRI capability to perform fully instrumented RIA tests in PWR conditions and to provide highly valuable results for RIA phenomena modelling (boiling crisis, post-failure events), for code validation, and for assessing PWR safety criteria. Highlights• The CABRI international Program (CIP) tests industrial irradiated fuel rods in a circulating test loop ensuring prototypical PWR conditions.• The CABRI reactor provides experimental conditions and power pulses representative of PWR RIA transients.• A complete instrumentation is available: online fuel motion monitoring system (Hodoscope), instrumented test device, pre-test and post-test non-destructive examination (IRIS).• Results will help modelling, code qualification and validation, and provide a new technical basis for PWR fuel safety criteria assessment for RIA conditions.

No abstract

This paper presents an experimental application of Distributed Optical Fiber Sensors (DOFS) for the Structural Health Monitoring (SHM) of concrete structures affected by internal swelling pathologies. In the framework of a large research project aiming to assess the possible extension of the operating lifetime of nuclear power plants from 40 to 60 years, massive blocks were cast from reactive concrete mixtures intended to develop delayed ettringite formation and alkali–silica reaction. These blocks were subjected to specific ageing conditions to initiate and accelerate the concrete pathologies. Some of the blocks were instrumented with DOFS bonded to the surface and embedded in the concrete. Using an interrogator device based on Rayleigh backscattering and a suitable procedure to eliminate temperature effects, distributed strain measurements were then performed at different time intervals. The first results of this ongoing study made it possible to demonstrate the feasibility and effectiveness of this sensing technology for detecting and monitoring expansion induced by swelling pathologies in representative-scale concrete structures.