Over the last decades, porphyrin sensitizers have made a remarkable contribution to performance improvement in dye-sensitized solar cells (DSSCs). In particular, versatile push–pull-type porphyrin sensitizers have achieved power conversion efficiencies (η) over 10% as a result of their improved light-harvesting abilities. Meanwhile, aromatic ring fusion to a porphyrin core is an attractive option for highly efficient DSSCs because of its expanded π-conjugation and resultant red-shifted absorption. Nevertheless, aromatic-fused porphyrin sensitizers have suffered rather low cell performances due to their mismatch of HOMO–LUMO levels, high aggregation tendency, and short lifetime of the excited states. Bearing these in mind, we envisioned that the fusion of substituted methylene-bridged small aromatic ring to a porphyrin core would overcome these drawbacks, boosting the cell performance. Herein, we report a series of substituted methylene-bridged thiophene-fused porphyrins, AfZnP, DfZnP, and DfZnP- i Pr. After optimization, DSSC with the donor-side thiophene-fused DfZnP- i Pr achieved an η-value of 10.1%, which is comparable to that of DSSC with GY50 (10.0%), a representative high-performance push–pull-type porphyrin sensitizer. More importantly, cosensitization of DfZnP- i Pr with a complementary sensitizer LEG4 further led to an η-value of 10.7%, which is the highest value ever reported for DSSCs with fused porphyrin sensitizers. Therefore, our strategy will reboot the exploration of aromatic-fused porphyrin sensitizers for high-performance DSSCs.

A tropolone group has been employed for the first time as an anchoring group for dye-sensitized solar cells (DSSCs). The DSSC based on a porphyrin, YD2-o-C8T, with a tropolone moiety exhibited a power-conversion efficiency of 7.7 %, which is only slightly lower than that observed for a reference porphyrin, YD2-o-C8, with a conventional carboxylic group. More importantly, YD2-o-C8T was found to be superior to YD2-o-C8 with respect to DSSC durability and binding ability to TiO2 . These results unambiguously demonstrate that tropolone is a highly promising dye-anchoring group for DSSCs in terms of device durability as well as photovoltaic performance.

To evaluate the effects of substituent bulkiness around a porphyrin core on the photovoltaic properties of porphyrin-sensitized solar cells, long alkoxy groups were introduced at the meso-phenyl group (ZnPBAT-o-C8) and the anchoring group (ZnPBAT-o-C8Cn, n = 4, 8) of an asymmetrically substituted push-pull porphyrin with double electron-donating diarylamino groups and a single electron-withdrawing carboxyphenylethynyl anchoring group. The spectroscopic and electrochemical properties of ZnPBAT-o-C8 and ZnPBAT-o-C8Cn were found to be superior to those of a push-pull porphyrin reference (YD2-o-C8), demonstrating their excellent light-harvesting and redox properties for dye-sensitized solar cells. A power conversion efficiency (η) of the ZnPBAT-o-C8-sensitized solar cell (η = 9.1%) is higher than that of the YD2-o-C8-sensitized solar cell (η = 8.6%) using iodine-based electrolyte due to the enhanced light-harvesting ability of ZnPBAT-o-C8. In contrast, the solar cells based on ZnPBAT-o-C8Cn, possessing the additional alkoxy chains in the anchoring group, revealed the lower η values of 7.3% (n = 4) and 7.0% (n = 8). Although ZnPBAT-o-C8Cn exhibited higher resistance at the TiO2-dye-electrolyte interface by virtue of the extra alkoxy chains, the reduced amount of the porphyrins on TiO2 by excessive addition of coadsorbent chenodeoxycholic acid (CDCA) for mitigating the aggregation on TiO2 resulted in the low η values. Meanwhile, the ZnPBAT-o-C8-sensitized solar cell showed the lower η value of 8.1% than the YD2-o-C8-sensitized solar cell (η = 9.8%) using cobalt-based electrolyte. The smaller η value of the ZnPBAT-o-C8-sensitized solar cell may be attributed to the insufficient blocking effect of the bulky substituents of ZnPBAT-o-C8 under the cobalt-based electrolyte conditions. Overall, the alkoxy chain length and substitution position around the porphyrin core are important factors to affect the cell performance.

At ropolone group has been employed for the first time as an anchoring group for dye-sensitized solar cells (DSSCs). The DSSC based on aporphyrin, YD2-o-C8T, with atropolone moiety exhibited apower-conversion efficiency of 7.7 %, whichi so nly slightly lower than that observed for ar eference porphyrin, YD2-o-C8,w ith ac onventional carboxylic group.More importantly, YD2-o-C8T was found to be superior to YD2-o-C8 with respect to DSSC durability and binding ability to TiO 2 .T hese results unambiguously demonstrate that tropolone is ah ighly promising dye-anchoring group for DSSCs in terms of device durability as well as photovoltaic performance.

A hydroxamic acid group has been employed for the first time as an anchoring group for cobalt-based dye-sensitized solar cells (DSSCs). The porphyrin dye YD2-o-C8HA including a hydroxamic acid anchoring group exhibited a power conversion efficiency (η) of 6.4 %, which is close to that of YD2-o-C8, a representative porphyrin dye incorporating a conventional carboxylic acid. More importantly, YD2-o-C8HA was found to be superior to YD2-o-C8 in terms of both binding ability to TiO and durability of cobalt-based DSSCs. Notably, YD2-o-C8HA photocells revealed a higher η-value (4.1 %) than YD2-o-C8 (2.8 %) after 500 h illumination. These results suggest that the hydroxamic acid can be used for DSSCs with other transition-metal-based redox shuttle to ensure high cell durability as well as excellent photovoltaic performance.