Untitled

Tselios, Ch.; Bikiaris, D.; Savidis, P.; Panayiotou, Costas; Larena, A.

doi:10.1023/a:1004434412273

Cited by 30 publications

(22 citation statements)

References 23 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…A comparative study of the same type of PP reinforced with E-and Mtype glass fibers (6 mm in length) showed an increase of impact strength from 6 J/m to 14 and 16 J/m, respectively. 12 This comparison reveals PROPERTIES OF BASALT FIBER-REINFORCED PP the real capabilities of basalt fibers for reinforcing of the isotactic polypropylene (iPP) matrix. The poor adhesion between the iPP matrix of the above-discussed samples and untreated basalt fibers was found on the fracture surfaces by SEM observation (Fig.…”

Section: Mechanical Propertiesmentioning

confidence: 94%

Mechanical properties and viscoelastic behavior of basalt fiber-reinforced polypropylene

Botev

Betchev

Bikiaris

et al. 1999

J. Appl. Polym. Sci.

Self Cite

160

100

View full text Add to dashboard Cite

ABSTRACT:In the present article, a series of commercial-grade polypropylenes (PP) filled with different contents of short basalt fibers were studied. This composite material presented deterioration of both mechanical characteristics, for example, stress and strain at yield with increasing of the fiber content. On the other hand, the impact strength was fourfold higher than that of unfilled PP. A poor adhesion between the PP matrix and the basalt fibers was detected. This is why interfacial interactions were promoted by the adding of poly(propylene-g-maleic anhydride) (PP-g-MA). It was observed that the tensile properties of the obtained materials and their impact strengths increased significantly with increasing of the amount of PP-g-MA in the blend. The adhesion improvement was confirmed by scanning electron microscopy as well. Fourier transform infrared spectroscopy was applied to assess if any chemical interactions in the system PP/PP-g-MA/basalt fibers exist. Dynamic mechanical thermal analysis data showed an increase of the storage modulus with increasing fiber content. The conclusion was made that the modification of the PP matrix led to a higher stiffness but its value remained constant, irrespective of the PP-g-MA content. With increasing fiber content, damping in the ␤-region decreased, but increase of the coupling agent content restored its value back to that of PP. The loss modulus spectra presented a strong influence of fiber content on the ␣-relaxation process of PP. The position of the peaks of the above-mentioned relaxation processes are discussed as well.

show abstract

Section: Mechanical Propertiesmentioning

confidence: 94%

Mechanical properties and viscoelastic behavior of basalt fiber-reinforced polypropylene

Botev

Betchev

Bikiaris

et al. 1999

J. Appl. Polym. Sci.

Self Cite

160

100

View full text Add to dashboard Cite

show abstract

“…The mechanical performances of PP can be further enhanced by adding inorganic fillers. The most commonly used low-cost fillers for PP include talc, calcium carbonate, short glass fiber and mica [1][2][3][4][5][6]. However, a large volume fraction of fillers, ca [25][26][27][28][29][30] % is needed to achieve desired mechanical properties.…”

Section: Introductionmentioning

confidence: 99%

Structure and Mechanical Behavior of Isotactic Polypropylene Composites Filled with Silver Nanoparticles

Tjong

Bao

2007

E-Polymers

View full text Add to dashboard Cite

Isotactic polypropylene (PP) nanocomposites containing 0.1, 0.3, 0.5 and 1.0 wt % silver (Ag) nanoparticles were prepared via melt compounding in a twin-screw extruder followed by injection molding The effects of the Ag nanoparticle additions on the structure and mechanical behavior of PP were studied using DSC, WXRD, optical microscopy, tensile and Izod impact techniques. DSC and WXRD measurements showed that the addition of only 0.1 wt% Ag nanoparticles promote the formation of β-form PP. Further increasing Ag content would not lead to additional increase of the β-PP phase content. The induced β-form PP phase is beneficial to enhance the impact strength and tensile ductility of the PP/Ag nanocomposites.

show abstract

“…also by the properties of the formed interphase, in particular, its thickness and strength (2)(3)(4). One of the effective ways of creating interphase and, in this way, controlling composite properties is fiber surface treatment (5, 6) using sizings and film formers or coupling agents.…”

Section: Introductionmentioning

confidence: 99%

Effect of Silane Coupling Agent on Interphase and Performance of Glass Fibers/Unsaturated Polyester Composites

Park

Jin

2001

Journal of Colloid and Interface Science

168

View full text Add to dashboard Cite

Untitled

Cited by 30 publications

References 23 publications

Mechanical properties and viscoelastic behavior of basalt fiber-reinforced polypropylene

Mechanical properties and viscoelastic behavior of basalt fiber-reinforced polypropylene

Structure and Mechanical Behavior of Isotactic Polypropylene Composites Filled with Silver Nanoparticles

Effect of Silane Coupling Agent on Interphase and Performance of Glass Fibers/Unsaturated Polyester Composites

Contact Info

Product

Resources

About