A comparative study between different modulations techniques used in field oriented control induction motor drive

Banerjee, Tista; Bera, Jitendranath; Chowdhuri, Sumana; Sarkar, Gautam

doi:10.1109/ciec.2016.7513777

Cited by 8 publications

(7 citation statements)

References 12 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Discretization of voltage has a negative impact that is, an imperceptible amount of subharmonics is generated while synthesizing the periodic waveforms [113,114]. In order to obtain an indistinguishable output, DM-CC should be switched at a seven times higher frequency compared to PWM modulator [113,115].…”

Section: 1 Discrete Modulation Current Controller (Dm-cc)mentioning

confidence: 99%

See 1 more Smart Citation

Review on Current Control Techniques of Grid Connected PWM-VSI Based Distributed Generation

2019

View full text Add to dashboard Cite

Nowadays, new trends in the industry of electricity generation are to enhance the power generation by employing distributed generation (DG) system which is mostly based on renewable generation sources such as wind, solar, etc. However, many power quality problems could arise on existing grid when DG is connected or the operation of distributed energy resources (DER) is not controlled properly. That's why, while integrating DG with the power grid, a seamless attention should be given to power generation and safe running of system. Several methods, having a diverse concept, have been divided into two main sets: linear and nonlinear controllers. The first group comes with PI controller and parameter feedback controller, and control by means of constant frequency with predictive techniques. The second group includes hysteresis current control and on-line optimization for predictive controllers. Additionally, new current control techniques with neural networks and fuzzy based controllers are also discussed. Selected methods associate the arrangement for the sake to demonstrate the described groups of the controller.

show abstract

Section: 1 Discrete Modulation Current Controller (Dm-cc)mentioning

confidence: 99%

“…Primarily, the fuzzy logic controller is utilized as a replacement for the conventional proportional and integral controller [114], [118]. The principal block diagram of a fuzzy-tuned PI controller, together with the fuzzy inference system is shown in Fig.…”

Section: Fuzzy Logic (Fl) Based Current Controllermentioning

confidence: 99%

Review on Current Control Techniques of Grid Connected PWM-VSI Based Distributed Generation

2019

View full text Add to dashboard Cite

show abstract

“…In case the reference control signal is the voltage signals, the Pulse Width Modulation (PWM) method can be used to produce the switching pulse to control the inverter. In case this signal is current, the hysteresis current control method can be used for generating the switching pulses [13,14]. Although the current of IMD applying HC method is high ripple, however, due to its simple structure, low switching losses, and fast response, the HC method is preferred in practice [15,16].…”

Section: Introductionmentioning

confidence: 99%

“…Therefore, determining the rotor flux angle is extremely important in the FOC method with the HC controller. A typical FOC applied for HC controller with the flux angle calculating form integral algorithm is presented in [13,17,18]. The simulation results have demonstrated the effectiveness of this method.…”

Section: Introductionmentioning

confidence: 99%

“…As a result, this control method may meet some problems in the actual operation when the value of the rotor flux angle overcomes the data type limitations. This paper reviews the typical FOC method used for the HC controller in [13,17,18] and then proposes an improvement based on the current model for calculating the rotor flux angle. The result is that the estimated flux angle is a periodic function.…”

Section: Introductionmentioning

confidence: 99%

See 1 more Smart Citation

An Improving Hysteresis Current Control Method Based on FOC Technique for Induction Motor Drive

Tran

Brandštetter

Dinh

et al. 2021

J. ADV. ENG. COMPUT.

View full text Add to dashboard Cite

The paper presents an improving speed control method using a field-oriented control (FOC) technique for the hysteresis current (HC) controller in the induction motor drive. The basic principle of a controller applying hysteresis band current is comparing reference currents and the measured currents to generate switching pulses for controlling an inverter. In the typical FOC for the HC controller, the rotor flux angle’s value will increase to infinity due to the integral algorithm’s error accumulation. This problem can lead to the faulty operation of the induction motor drive (IMD) system. In this paper, a current model with the advantage of precisely determining the periodic rotor flux angle is used in the FOC technique to provide reference currents for the current controller. The rotor flux angle will periodically change according to the motor speed in the range [-π π] during the operation of IMD. The operation of the induction motor drive is implemented and tested by MATLAB/SIMULINK software. The simulation results have demonstrated the effectiveness of the HC control method-based FOC technique with periodic rotor flux angle in controlling motor speed. This is an Open Access article distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium provided the original work is properly cited.

show abstract

Dynamic Modelling and Co-simulation Between MATLAB–Simulink and DIgSILENT PowerFactory of Electric Railway Traction Systems

Chiza¹,

Cepeda

Riofrio

et al. 2020

Power Systems

View full text Add to dashboard Cite

A comparative study between different modulations techniques used in field oriented control induction motor drive

Cited by 8 publications

References 12 publications

Review on Current Control Techniques of Grid Connected PWM-VSI Based Distributed Generation

Review on Current Control Techniques of Grid Connected PWM-VSI Based Distributed Generation

An Improving Hysteresis Current Control Method Based on FOC Technique for Induction Motor Drive

Dynamic Modelling and Co-simulation Between MATLAB–Simulink and DIgSILENT PowerFactory of Electric Railway Traction Systems

Contact Info

Product

Resources

About