A Material-Balance Equation for Stress-Sensitive Shale-Gas-Condensate Reservoirs

Abstract

Summary During the last few years, production of liquid hydrocarbons has been reported from the gas-condensate window of the Eagle Ford, Barnett, Niobrara, and Marcellus shale plays in the US. This paper presents a new material-balance equation (MBE) for estimation of original gas in place (OGIP) and original condensate in place (OCIP) in shale-gas-condensate reservoirs. This material-balance methodology allows estimating the critical time for implementing gas injection in those cases in which condensate buildup represents a problem. In addition, the proposed MBE considers the effects of free, adsorbed, and dissolved gas-condensate production, and also takes into account the stress-dependency of porosity and permeability. An extension of the methodology is implemented for estimating the optimum time for hydraulically refracturing shale-condensate reservoirs. The new MBE applies to shale-gas-condensate reservoirs by incorporating a two-phase gas-deviation factor (Z2) and total cumulative gas production (Gpt) that includes both gas and condensate. If a crossplot of P/Z2 (pressure/Z2) vs. Gpt is prepared for a conventional gas-condensate reservoir, a single straight line is obtained. However, when the single-phase gas-compressibility factor (Z) is used, a deviation from the linear behavior is observed after the reservoir pressure falls below the gas dewpoint. This methodology is applied in this study to unconventional shale-gas condensate. Because there are three characteristic stages of production in a shale-gas reservoir (production of free, adsorbed, and dissolved gas), the location of the aforementioned deviation will provide a hint of the production stage that will be affected by condensate buildup. For example, if the deviation point is in the region where production of free gas is predominant, then the production caused by desorption mechanisms will be negatively affected because condensation will have already occurred in the reservoir, resulting in reduction of effective permeability to gas. This methodology then allows estimating the critical time for implementing gas injection on the basis of the total cumulative gas production. The method also permits estimating the optimum time for refracturing. The refracturing can be of a normal size for a given shale (similar to the original fracturing job), or it can be a superfrac job. Results are presented as crossplots of (1) P/Z2 vs. Gpt, (2) Gpt vs. time, and (3) gas rate vs. time. It is concluded that estimation of the critical time for implementing gas injection is useful for improving the performance of those shale-gas-condensate reservoirs in which condensate buildup represents a threat that can negatively affect the gas-production rate. The novelty of this work resides on the fact that the combined effect of free, adsorbed, and dissolved gas-production mechanisms on stress-sensitive shale-gas-condensate reservoirs had not been considered previously in the literature for estimation of OGIP, OCIP, and reservoir performance with an analytical MBE. The inclusion of gas injection and refracturing had not been considered either.

A Critical Review on Material Balance Equation

“…Some researchers are expecting that this type of gas will increase the energy supply throughout the world. Multiple porosities are the important characteristics of Shale gas reservoirs (Orozco and Aguilera 2017). These multiple porosities are: (i) adsorbed porosity, (ii) organic porosity, (iii) inorganic matrix porosity, (iv) natural fractures porosity, and (v) hydraulic fractures porosity (Aguilera and Lopez, 2013).…”

Reasonable Pumping Depth for Drainage and Gas Recovery of Shale Gas Wells

“…The large-scale development of shale gas benefited from the significant advancement in horizontal well completion and segmented volume fracturing reconstruction technologies. After a horizontal well is fractured in segments, an extremely complex fracture grid system will be created, and these fracture grids will greatly improve the permeability of the reservoirs within the fracturing communication range, enabling the originally abnormally dense shale reservoirs to be effectively connected to the wellbore, so that the development of shale gas could have commercial values [7][8][9]. The desorption effect of adsorbed gas and the complex fracture network formed after segmented fracturing make the shale gas wells exhibit different dynamic production characteristics from the conventional gas wells [10,11].…”

Modeling of Material Balance From the Experimental Ucg

“…In this paper, the content of moisture and ash of the combustible working material was used to determine the elemental composition of the petroleum product. The materialbalance equation for the estimation of the gas and condensate in place in shale-gas-condensate reservoirs has been described in [21]. The task of this materialbalance is estimating the critical time for using the gas injection when the condensate buildup represents a problem.…”