A Modified P&amp;O Maximum Power Point Tracking Method With Reduced Steady-State Oscillation and Improved Tracking Efficiency

Ahmed, Jubaer; Salam, Zainal

doi:10.1109/tste.2016.2568043

Cited by 357 publications

(232 citation statements)

References 28 publications

Supporting

Mentioning

231

Contrasting

Unclassified

Order By: Relevance

“…Therefore, this paper aims firstly to extract lacking parameters in the manufacturers' datasheet by using a simple tool provided by MathWorks [11] and then model the PV panel. The single-diode model is used in this work because it gives a high compromise between accuracy and simplicity [12], and several researchers have used it in their works [13,14]. In addition, this work shows the effect of parameters that may change the performance of the PV panel.…”

Section: Introductionmentioning

confidence: 99%

Modeling of Photovoltaic System with Modified Incremental Conductance Algorithm for Fast Changes of Irradiance

Motahhir¹,

Ghzizal²,

Sebti³

et al. 2018

International Journal of Photoenergy

137

View full text Add to dashboard Cite

The first objective of this work is to determine some of the performance parameters characterizing the behavior of a particular photovoltaic (PV) panels that are not normally provided in the manufacturers' specifications. These provide the basis for developing a simple model for the electrical behavior of the PV panel. Next, using this model, the effects of varying solar irradiation, temperature, series and shunt resistances, and partial shading on the output of the PV panel are presented. In addition, the PV panel model is used to configure a large photovoltaic array. Next, a boost converter for the PV panel is designed. This converter is put between the panel and the load in order to control it by means of a maximum power point tracking (MPPT) controller. The MPPT used is based on incremental conductance (INC), and it is demonstrated here that this technique does not respond accurately when solar irradiation is increased. To investigate this, a modified incremental conductance technique is presented in this paper. It is shown that this system does respond accurately and reduces the steadystate oscillations when solar irradiation is increased. Finally, simulations of the conventional and modified algorithm are compared, and the results show that the modified algorithm provides an accurate response to a sudden increase in solar irradiation.

show abstract

Section: Introductionmentioning

confidence: 99%

Modeling of Photovoltaic System with Modified Incremental Conductance Algorithm for Fast Changes of Irradiance

Motahhir¹,

Ghzizal²,

Sebti³

et al. 2018

International Journal of Photoenergy

137

View full text Add to dashboard Cite

show abstract

“…The maximum power point tracking (MPPT) is done by the control of the duty cycle in the DC‐DC converter. In general, in order to increase the efficiency and reduce the cost of PV panels, the electrical energy is extracted by applying MPPT methods …”

Section: Introductionmentioning

confidence: 99%

“…In general, in order to increase the efficiency and reduce the cost of PV panels, the electrical energy is extracted by applying MPPT methods. 5,6 To solve the above-mentioned restrictions in PV panels, many high step-up DC-DC converters have been presented. In the phase-shifted full-bridge converter, the voltage gain is increased by increasing the winding turns of the used transformer.…”

mentioning

confidence: 99%

High step‐up DC‐DC converter with reduced voltage stress on devices

Babaei

Jalilzadeh

Sabahi

et al. 2018

Int Trans Electr Energ Syst

View full text Add to dashboard Cite

Summary The aim of this study is to propose a new nonisolated direct current (DC)–DC converter topology with high voltage gain and low voltage stress across the power devices. The proposed converter comprises a switch and n stages of inductor‐capacitor‐diode (L‐C‐D) units. Indeed, the proposed converter is based on the combination of the double‐boost and Single‐ended primary‐inductor converter (SEPIC), which is extended to n stages by adding L‐C‐D units. As a consequence, the proposed converter can generate higher voltage gains with small values of the switch duty cycle, which increase the controllability of the converter. Also, as the number of stages increases, the normalized voltage stress across the power devices is reduced. As a result, the Metal Oxide Semiconductor Field Effect Transistor (MOSFET) switch with low RDS‐on and devices with reduced nominal voltage can be used in the proposed converter. Furthermore, another advantage of the proposed converter is that the percentage of input current ripple is low. The voltage and current stresses of the power devices are analyzed. The circuit performance is compared with other high step‐up structures in the literature in terms of voltage gain and normalized voltage stress. The mathematical analysis and circuit performance of the proposed topology are verified by experimental results.

show abstract

“…This paper focuses on the P&O algorithm because of its advantages, for example it can be implemented in analog and digital form, does not require periodic, efficient and easy to implement [2] [3] [8]. The P & O algorithm depend on the slope of the PV characteristic.…”

Section: Introductionmentioning

confidence: 99%

Design And Implementation Soft-switching MPPT SEPIC Converter Using P&O Algorithm

et al. 2018

View full text Add to dashboard Cite

Abstract. This paper presents details of design and implementation of Maximum Power Point Tracking (MPPT) SEPIC Converter to maximize Photovoltaic (PV) power output. Perturb and observe (P & O) algorithm has been used as a tracking technique to determine MPPT. This algorithm are simple and efficient to determine the maximum power point (MPP). The soft-switching method will be added to the implementation of MPPT SEPIC Converter to reduce switching losses. The results show that the proposed MPPT method implementation can increase the output power of PV.

show abstract

A Modified P&O Maximum Power Point Tracking Method With Reduced Steady-State Oscillation and Improved Tracking Efficiency

Cited by 357 publications

References 28 publications

Modeling of Photovoltaic System with Modified Incremental Conductance Algorithm for Fast Changes of Irradiance

Modeling of Photovoltaic System with Modified Incremental Conductance Algorithm for Fast Changes of Irradiance

High step‐up DC‐DC converter with reduced voltage stress on devices

Design And Implementation Soft-switching MPPT SEPIC Converter Using P&O Algorithm

Contact Info

Product

Resources

About