A technique for border molding with light-polymerized resin

Olivieri, Alejandro C.; Zuccari, A; Olivieri, D

doi:10.1016/s0022-3913(03)00262-2

Cited by 5 publications

(3 citation statements)

References 0 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…We found that in group I, the overall mean value was 4.59 ± 0.81, in group II, it was 4.7 ± 0.81, and in group III, it was 6.72 ± 0.81. These findings are comparable to and in agreement with the study results of Olivieri et al 12 Al-Judy 13 conducted a study of comparison of the effect of sectional border molding using different molding and final impression materials on the retention of maxillary complete denture bases among 14 completely edentulous patients. Retention with denture bases obtained from full and posterior putty silicone border molding combined with the light body silicone was higher as compared with those obtained from other tracing procedure.…”

Section: Discussionsupporting

confidence: 88%

Evaluation and Comparison of the Effect of Different Border Molding Materials on Complete Denture Retention: An in vivo Study

Pachar¹,

Singla²,

Kumar³

2018

The Journal of Contemporary Dental Practice

View full text Add to dashboard Cite

show abstract

Section: Discussionsupporting

confidence: 88%

Evaluation and Comparison of the Effect of Different Border Molding Materials on Complete Denture Retention: An in vivo Study

Pachar¹,

Singla²,

Kumar³

2018

The Journal of Contemporary Dental Practice

View full text Add to dashboard Cite

show abstract

“…Olivieri et al . [ 11 ] described a technique for border molding using light polymerized resin. Solomon[ 12 ] studied the single stage silicone border molded closed mouth impression technique.…”

Section: Discussionmentioning

confidence: 99%

Comparative evaluation of reproducibility of peripheral tissues produced by different border molding materials in edentulous patients: An in vivo study

Arora

Goyal

Sehgal

2015

J Indian Prosthodont Soc

View full text Add to dashboard Cite

Aim:The aim of the study is to analyze the effect of different materials and techniques in current use on peripheral shaping of complete denture impression.Methods:The present study was conducted to compare and evaluate the maxillary border morphology produced using tissue conditioner as control and low fusing impression compound, Polyether, Pattern resin and periphery wax as border molding materials. The study was carried out on 15 denture wearer patients with well formed, rounded edentulous maxillary arch with adequate width and height. On each patient, border moldings were done, with tissue conditioner which was loaded on the borders of previous maxillary denture of the patient (control group), low fusing impression compound (Group 1), polyether (Group 2), Pattern resin (Group 3) and Peripheral wax (Group 4), respectively on special tray made for the patient. Sulcus width height and area was then measured for each group using stereomicroscope.Results and Conclusions:Based on the study it is concluded that the polyether was the best material for border molding which will give most accurate borders to a denture.

show abstract

“…Border molding considered to be as an important step in the complete denture fabrication since the retention of complete denture depend on several factors as the biological ,physical and mechanical these factors could be achieved by mean of an accurate border molding followed by an accurate final impression (6) .…”

Section: Introductionmentioning

confidence: 99%

Comparative Analysis of the Effect of Border Molding Using Different Molding and Final Impression Materials on the Retention of Complete Denture Bases

Ammar

Mustafa

El-Haleim

2020

Al-Azhar Assiut Dental Journal

View full text Add to dashboard Cite

Aim : It is for comparing the retention of complete denture bases made by border molding using the low fusing compound and putty type condensation silicon by using metallic zinc-oxide eugenol and medium body condensation silicon as final impression material.. Subjects and Methods: the study was carried out on 20 patients , the selected was completely edentulous with well-developed ridge four dentures for each patient was fabricated :(Group A):border molding with green stick compound and final impression with zinc oxide eugenol(Group B): border molding with green stick compound and medium body rubber base as a final impression(Group C): border molding with putty type and medium body condensation silicon as a final impression materials(Group D): border molding with putty type condensation silicon and medium body rubber base as a final impression. Results: Statistically significant results were in complete denture obtained from putty type border molding and medium body condensation silicon final impression, while the least values obtained from green stick border molding and zinc oxide eugenol final impression. Conclusion: Based on the favourable results of this study , it can summarized that the complete denture obtained from putty type and medium body condensation silicone more retentive than other complete dentures obtained from other border molding and final impression materials.

show abstract

A technique for border molding with light-polymerized resin

Cited by 5 publications

References 0 publications

Evaluation and Comparison of the Effect of Different Border Molding Materials on Complete Denture Retention: An in vivo Study

Evaluation and Comparison of the Effect of Different Border Molding Materials on Complete Denture Retention: An in vivo Study

Comparative evaluation of reproducibility of peripheral tissues produced by different border molding materials in edentulous patients: An in vivo study

Comparative Analysis of the Effect of Border Molding Using Different Molding and Final Impression Materials on the Retention of Complete Denture Bases

Contact Info

Product

Resources

About