An assessment of the process of Self-propagating High-Temperature Synthesis for the fabrication of porous copper composite

Moloodi, Ahmad; Raiszadeh, Ramin; Vahdati-Khaki, Jalil; Babakhani, Abolfazl

doi:10.1016/j.jallcom.2009.07.152

Cited by 10 publications

(6 citation statements)

References 21 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…In the SHS method, copper oxide and aluminum are used as raw materials for fabrication of Cu-Al 2 O 3 nanocomposite. Mixing condition and compaction pressure are two important factors in the SHS method [6][7][8].…”

Section: Introductionmentioning

confidence: 99%

One-step fabrication of Cu–Al2O3 nanocomposite via solution combustion synthesis route

Nasiri

Khaki

Zebarjad

2011

Journal of Alloys and Compounds

View full text Add to dashboard Cite

Section: Introductionmentioning

confidence: 99%

One-step fabrication of Cu–Al2O3 nanocomposite via solution combustion synthesis route

Nasiri

Khaki

Zebarjad

2011

Journal of Alloys and Compounds

View full text Add to dashboard Cite

“…The positive points of this method include the preparation of affordable and easy compact powder of raw materials, low-temperature process, process flexibility in controlling the microstructure and chemical composition of the products. Therefore, the main application of this process has been the production carbides, nitrides and aluminides which needs high temperature furnaces and relatively long processing times [5][6][7].…”

Section: Introduction *mentioning

confidence: 99%

Fabrication of Iron Aluminide Coatings (Fe3Al and FeAl3) on Steel Substrate by Self-Propagating High Temperature Synthesis (SHS) Process

Mohammadkhani

Bondar

Vahdati-Khaki

et al. 2017

J. Coat. Sci. Technol.

Self Cite

View full text Add to dashboard Cite

Iron aluminides (Fe3Al and FeAl3) coatings were fabricated on a steel substrate by selfpropagating high temperature synthesis (SHS) method. Raw materials, Fe and Al powders, were mixed at two different stoichiometry ratios (3:1 and 1:3). The mixtures and the substrate were placed in a furnace at 950 °C to ignite the SHS process. Coating phases were investigated using X-ray diffraction (XRD) and Energy Dispersive Spectroscopy (EDS). The microstructure of the coatings was analyzed with optical microscopy (OM) and scanning electron microscopy (SEM). The results confirmed that it is possible to produce Fe3Al and FeAl3 coatings on steel substrate using SHS method. In addition, the results show that the coatings were composed of two different phases and their microstructures were non-porous and dense. Wear resistance of the coatings were higher than that of the substrate.

show abstract

“…Al 2 O 3 /Cu composites have been extensively investigated, the presence of metal particles, such as copper, in Al 2 O 3 improves the toughness and electrical properties of this material [10][11][12][13]. Up to now, just one work about Al 2 O 3 /Cu foams was found; these foams were fabricated by self-propagating high-temperature synthesis (SHS) [14].…”

Section: Introductionmentioning

confidence: 99%

Alumina/copper foams produced by replica using a double impregnation process

Granados

Moreno

Vieira

et al. 2016

Advances in Applied Ceramics

View full text Add to dashboard Cite

Rheological behaviour of Al 2 O 3 and CuO suspensions was characterised in order to fabricate Al 2 O 3 /Cu foams as an alternative way to produce foams with better mechanical properties than common Al 2 O 3 foams. Different quantities of raw materials were combined to select the formulations for the ceramic-metal foams. Foams were produced by a double impregnation process, followed by a thermal cycle and a reduction cycle. In this work, materials were characterised trough zeta potential, SEM and optical dilatometry. Foams microstructure and compressive strength were evaluated. Final structures had a compressive resistance of 0.44 ± 0.14 MPa.

show abstract

An assessment of the process of Self-propagating High-Temperature Synthesis for the fabrication of porous copper composite

Cited by 10 publications

References 21 publications

One-step fabrication of Cu–Al2O3 nanocomposite via solution combustion synthesis route

One-step fabrication of Cu–Al2O3 nanocomposite via solution combustion synthesis route

Fabrication of Iron Aluminide Coatings (Fe3Al and FeAl3) on Steel Substrate by Self-Propagating High Temperature Synthesis (SHS) Process

Alumina/copper foams produced by replica using a double impregnation process

Contact Info

Product

Resources

About