An easily organic–inorganic hybrid optical sensor based on dithizone impregnation on mesoporous SBA‐15 for simultaneous detection and removal of Pb(II) ions from water samples: Response‐surface methodology

Abstract

In this study, a novel organic-inorganic hybrid adsorbent for single-step detection and removal of Pb(II) ions based on dithizone (DZ) anchored on mesoporous SBA-15 was fabricated. The designed solid optical sensor revealed rapid colorimetric responses and high selectivity. Central composite design (CCD) combined with desirability function (DF) was applied to evaluate the interactive effects and optimization of important variables such as pH value, mesoporous SBA-15 dosage, contact time and initial concentration of Pb(II) ions and optimum conditions for each of the factors were obtained 6.0, 25 mg, 30 min and 20 μg ml − 1 , respectively. This adsorbent or solid optical chemo sensor exhibited a linear range of 1.0 to 100.0 μg ml −1 of Pb(II) ion concentration with a detection limit of 0.07 μg ml −1 . This adsorbent was applied to determine and remove the Pb(II) in spiked samples. Various isotherm models such as Langmuir, Freundlich, Temkin and Dubinin-Radushkevich were studied for fitting the experimental equilibrium data. Langmuir model was chosen as an efficient model. Various kinetic models such as pseudo-first, second order intraparticle, diffusion models were studied for analysis of experimental adsorption data and the pseudo second order model was chosen as an efficient model. KEYWORDS central composite design, mesoporous SBA-15, organic-inorganic hybrid, Pb(II) ions, solid optical sensor

Simultaneous removal of Cu2+ and Cr3+ ions from aqueous solution based on Complexation with Eriochrome cyanine‐R and derivative spectrophotometric method

“…Kinetic models based on Elovich, pseudo first and second‐order and intraparticle diffusion give good knowledge about the rate and mechanism of an adsorption process. In the pseudo‐first‐order model, by plotting of the log (qe‐qt) versus t, k 1 and qe values can be calculated by slop and intercept of this plot, respectively (See Table ) . The distance among experimental qe value with intercept indicate that this model not suitable to explain experimental data.…”

Zinc oxide nanorod‐loaded activated carbon for ultrasound‐assisted adsorption of safranin O: Central composite design and genetic algorithm optimization

“…The CCD method using Statistica 10.0.228.8 software was used for the estimation, optimization and interactive effects of adsorption parameters on removal of SO dye from aqueous solution …”

“…The CCD method using Statistica 10.0.228.8 software was used for the estimation, optimization and interactive effects of adsorption parameters on removal of SO dye from aqueous solution. [24][25][26][27] The present CCD was based on various parameters affecting the ultrasonic-assisted removal efficiency, including initial concentration of SO (X 1 ), pH (X 2 ), amount of adsorbent (X 3 ) and sonication time (X 4 ), in randomized fashion to minimize the effects of the uncontrolled factors. Therefore, a five-level CCD was performed to evaluate the influence of these quantities on removal efficiency ( Table 1).…”

Removal of Ni (II) By Sol-Gel Silica Functionalized With Efficient Metal Chelating Agents

“…Previously metal chelating agents such as 4-(2-thiazolylazo) resorcinol, 1-(2-Thiazolylazo)-2-naphthol, Diethyl ammonium diethyl dithiocarbamate, 5-methyl-4-(thiazol-2-yldiazenyl) benzene-1, 3-diol, trithiane, dithizone, dithiocarbamate, Schiff base and dimethylglyoxime have been used for the preparation of modi ed silica for the sorption of metal ions [18][19][20][21][22][23][24][25].…”