An Essential Studies on Tribology’s: A Short Review

Jamaludin, Ahmad Shahir; Sazali, Norazlianie; Ngadiman, Nor Hasrul Akhmal

doi:10.37934/arfmts.72.1.18

Cited by 5 publications

(2 citation statements)

References 28 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Adsorption is one of the ways that salts and minerals can be eliminated from seawater. To date, the adsorption approach has been greatly employed since it is a simple, highefficiency removal method [6,7]. Adsorption is a method for extracting a wide range of substances from wastewater, mainly from industrial sources [8].…”

Section: Introductionmentioning

confidence: 99%

Adsorption of Sodium Ion (Na+) onto Synthesized Zeolite-A from Malaysian Kaolin by Hydrothermal Method: Equilibrium and Kinetic Studies

Sazali¹,

Harun²,

Abdullahi³

et al. 2023

ARASET

View full text Add to dashboard Cite

Batch adsorption of sodium ion (Na+) using Malaysian kaolin-based materials, zeolite A was studied and observed. The experiments were done at different parameters such as varying initial concentrations of sodium ions in seawater solution (70 to 280 mg L–1), pH range of 6 to 8 and various adsorbent dosages (0.1 to 0.4g). The Langmuir and Freundlich's isotherms were used to analyse the data, and the results were compared. This study discovered that the Langmuir isotherm matched the experimental data very well, with the maximum monolayer adsorption capacities derived from the Langmuir equation being 769.3 mg g–1. Using pseudo-first-order, pseudo-second order, and intraparticle diffusion models, the kinetics of the reaction were further investigated and understood. The Intra Particle Diffusion Kinetic Equation was the most accurate description of the adsorption kinetics of sodium ions onto zeolite synthesis.

show abstract

Section: Introductionmentioning

confidence: 99%

Adsorption of Sodium Ion (Na+) onto Synthesized Zeolite-A from Malaysian Kaolin by Hydrothermal Method: Equilibrium and Kinetic Studies

Sazali¹,

Harun²,

Abdullahi³

et al. 2023

ARASET

View full text Add to dashboard Cite

show abstract

“…During machining process, contact between tool-chip-workpiece (shearing, sliding, rubbing etc. ), release energy in the form of heat, especially during metal machining [5][6][7][8][9][10]. Thermal deformation may occur if one element reaches an excessively high temperature, which might have a detrimental impact on the work or damage the equipment [7][8].…”

Section: Introductionmentioning

confidence: 99%

Analysis on Auger Pump Performance During Handling High Viscous Liquid

Alisha

Najwa²,

Jamaludin³

et al. 2022

JMMST

View full text Add to dashboard Cite

Viscosity is one of the factors affecting the performance of the auger pump. An auger pump is positive-displacement (PD) pump that moves fluids and semi-solid material along the screw axis using one or more screws. The study is about the analysis of the performance of the auger pump when transferring various viscosity liquids. In the study, a pumping device with auger shaft is designed. The sample liquids chosen for the experiment oil and concentrated detergent that poses various viscosity. The viscosity is being identified roughly by Zahn Cup Method with the temperature kept constant at 26°C throughout the measurement. The performance of the auger pump can be accessed by altering the motor speed in order to get various reading for the flow rate and pressure. It is found in the study; flowrate is affected by viscosity with the increasing motor speed. The study proves that the auger pump can operate with viscosity of 770 cSt liquid.

show abstract