Characterization on the coatings of Ni-base alloy with nano- and micron-size Sm2O3 addition prepared by laser deposition

Zhang, Shi Hong; Li, Ming Xi; Yoon, Junghyun; Cho, Tong Yul

doi:10.1016/j.matchemphys.2008.06.024

Cited by 16 publications

(12 citation statements)

References 19 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Within the nanoscaled form, amine functionalised-Sm2O3 nanobelts exhibit an improve of the electrochemical and optical properties of conducting and non-conducting polymers such as polypyrrole and poly(ethylene oxide) [9]. Zang et al [10] reported on the use of nano-sized particles of Sm2O3 to improve on the microhardness as well as the wear and corrosion resistance properties of Nickel-based alloys coatings. Numerous accounts of the role of Sm 3+ in heteregenous catalysis, phosphors for luminescent devices, medical diagnostics and therapeutic ends have been reported [11][12][13].…”

Section: -Introductionmentioning

confidence: 99%

Sm2O3 nanoparticles green synthesis via Callistemon viminalis' extract

Sone

Manikandan

Gurib-Fakim

et al. 2015

Journal of Alloys and Compounds

135

View full text Add to dashboard Cite

Section: -Introductionmentioning

confidence: 99%

Sm2O3 nanoparticles green synthesis via Callistemon viminalis' extract

Sone

Manikandan

Gurib-Fakim

et al. 2015

Journal of Alloys and Compounds

135

View full text Add to dashboard Cite

“…A series of fine dark areas that have been spread across the coating, and are rich in carbon and titanium can also be seen in the image. These are in fact the super saturated titanium carbide [30].…”

Section: Microstructure and Composition Of Coatingmentioning

confidence: 99%

Development of a TiC/Cr23C6 Composite Coating on a 304 Stainless Steel Substrate through a Tungsten Inert Gas Process

Hussain

Asmael

2017

Coatings

View full text Add to dashboard Cite

Abstract:The aim of this study was to develop a composite coating on 304 stainless steel employing a TIG (tungsten inert gas) process. Ti wire cored with graphite powder was used as the means of coating material. The process parameters were controlled to develop a coating with optimum characteristics (i.e., hardness and wear resistance). The microstructure of the coating was analyzed with SEM and XRD. It was found that both the hardness and the wear resistance increase as the current increases, while both of these properties decrease as travelling speed increases. It was found that the coated samples with composite layers were harder than the substrate and can range up to 1100 HV, almost 4.5 times higher than the hardness of 304 stainless steel. Likewise, the wear resistance of the coating was observed to be 4.5 times higher than that of the substrate. The high performance of the coating, as revealed by microstructural analysis, was due to the formation of TiC and Cr 23 C 6 . The optimum conditions for producing the coating are thus proposed to include a 120 A current and a 3.17 mm/s travel speed.

show abstract

“…A series of fine dark areas that have been spread across the coating, and are rich in carbon and titanium can also be seen in the image. These are in fact super saturated titanium carbide [23].…”

Section: Microstructure and Composition Of Coatingmentioning

confidence: 99%

Development of TiC/ Cr<sub>23</sub>C<sub>6 </sub>Composite Coating on St 304 Substrate through TIG Process

Hussain¹

2017

Preprint

View full text Add to dashboard Cite

Abstract:The aim of this paper is to develop a composite coating on St 304 steel employing TIG process. Ti wire cored with graphite powder is used as the means of coating material. The process parameters are varied in order to develop coating with optimum characteristics (i.e., hardness and wear resistance). The microstructure of the coating is analyzed with SEM and XRD. It is found that both of the hardness and wear resistance increase as the current increases while both of these properties decrease as the travelling speed increases. It is found that the coated samples with composite layers have more hardness than the substrate and it could range up to 1100 HV being almost 4.5 times higher than the hardness of St 304. Likewise, the wear resistance of coating is observed to be 4.5 times higher than that of substrate. The high performance of coating, as revealed by microstructural analysis, is due to formation of TiC and Cr23C6 .The optimum conditions to produce the coating are proposed to be 120 A current and 3.17 mm/s travel speed.

show abstract

Characterization on the coatings of Ni-base alloy with nano- and micron-size Sm2O3 addition prepared by laser deposition

Cited by 16 publications

References 19 publications

Sm2O3 nanoparticles green synthesis via Callistemon viminalis' extract

Sm2O3 nanoparticles green synthesis via Callistemon viminalis' extract

Development of a TiC/Cr23C6 Composite Coating on a 304 Stainless Steel Substrate through a Tungsten Inert Gas Process

Development of TiC/ Cr<sub>23</sub>C<sub>6 </sub>Composite Coating on St 304 Substrate through TIG Process

Contact Info

Product

Resources

About