Combustor performance enhancement through direct shear layer excitation

McManus, Keith; Vandsburger, Uri; Bowman, Craig T.

doi:10.1016/0010-2180(90)90079-7

Cited by 163 publications

(39 citation statements)

References 23 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…In the simulation of [2], small and large structures were predicted and the pressure spectrum showed 0.3 < St < 0.75. In the step experiments of [3,4,5], a mode with St = 0.1 persisted downstream, even when large frequency forcing was applied, the mode also coincided with a quarter wave acoustic mode. In [6], some peaks whose frequency scaled linearly with the flow velocity, almost independent of the acoustic conditions, were measured; these were typically low frequency modes.…”

Section: Evidencementioning

confidence: 99%

Shear flow-driven combustion instability: Evidence, simulation, and modeling

Ghoniem

Annaswamy

Wee

et al. 2002

Proceedings of the Combustion Institute

View full text Add to dashboard Cite

Combustion instability arises mostly due to the coupling between heat release dynamics and system acoustics; a condition elegantly stated by the Rayleigh criterion. In these cases, the acoustic field acts as the resonator, or pace maker, while the heat release dynamics, induced due to the impact of pressure or flow velocity perturbations on the equivalence ratio, flame length, residence time, shear layer, etc., supplies energy to support pressure oscillations. In this paper, we discuss another mechanism in which the resonator, or pace maker, may not be the acoustic field; instead it is an absolutely unstable shear layer mode acting as the source of sustained oscillations, which morph as large-scale eddies at a frequency different from acoustic modes. These perturb the flame motion and provide the energy to the acoustic field, acting here as an amplifier, to support pressure oscillations. We present evidence to the existence of this mechanism from several experiments where a pressure spectral peak can not be explained using acoustic analysis of the system, but instead matches the predicted absolute instability mode of the separated shear layer, and from numerical simulations. We also examine the impact of the mean velocity and temperature distribution on the frequency and growth rate to determine the dynamics leading to an absolute instability, and show that absolutely unstable modes are likely to arise at low equivalence ratios. In some cases, they can also be present at near stoichiometric conditions, i.e. only low and near unity stoichiometry can support an absolutely unstable mode. We use numerical simulation to distinguish between different unstable modes in the separating shear layer; the layer mode and the wake mode, and derive a reduced order model for the shear driven instability using POD analysis. Estimates of pressure amplitudes of fluid dynamic modes, when applied as forcing functions to the acoustic field, using this analysis compare favorably with experimental data.

show abstract

Section: Evidencementioning

confidence: 99%

Shear flow-driven combustion instability: Evidence, simulation, and modeling

Ghoniem

Annaswamy

Wee

et al. 2002

Proceedings of the Combustion Institute

View full text Add to dashboard Cite

show abstract

“…Active combustion control strategies that modulates the fuel flow rate [6][7][8][9][10][11][12][13], or air flow rate [14] can be applied to suppress thermoacoustic instabilities in premixed combustors by disrupting the coupling mechanisms that support these instabilities. While effective in suppressing the instabilities, these approaches require high speed actuators and add significant complexity to the design of the combustors.…”

Section: Introductionmentioning

confidence: 99%

Mitigation of thermoacoustic instability utilizing steady air injection near the flame anchoring zone

Altay

Hudgins

Speth

et al. 2010

Combustion and Flame

View full text Add to dashboard Cite

“…[13] . The amount of heat release rate perturbation q' in a typical backward facing step flow due to shear layer perturbations has been observed to be 15% in an experimental investigation in [32] and 25% in a numerical study in [33] of the mean heat release rate, q . Using a value of f q′ =0.15 q , the pressure amplitude at s rad / 603 = ω can be calculated using Eq.…”

Section: Acoustic Gain From Shear Layer Driven Heat Releasementioning

confidence: 99%

Reduced order modeling of reacting shear flow

Wee

Park²,

Yi³

et al. 2002

40th AIAA Aerospace Sciences Meeting &Amp; Exhibit

View full text Add to dashboard Cite

Thermoacoustic instability in premixed c ombustors occurs occasionally at multiple frequencies, especially in configurations where flames are stabilized on separating shear layers that form downstream of sudden expansions or bluff bodies. While some of these frequencies are related to the acoustic field, others appear to be related to shear flow instability phenomena. It is shown in this paper that shear flows can support self-sustained instabilities if they possess absolutely unstable modes. The associated frequencies are predicted using mean velocity profiles that resemble those observed in separating flows and for profiles obtained from numerical simulations, and are shown to match those derived from experimental and numerical investigations. It is also shown that the presence of density profiles compatible with premixed combustion can affect this frequency and can change the absolute instability mode into a convectively unstable mode thereby reducing the possibility of the generation of self-sustained oscillations. A qualitative prediction of the pressure amplitudes resulting from these shear layer modes is shown to be consistent with experimental measurements. The results from the stability analysis are combined with those using the Proper Orthogonal Decomposition (POD) method to yield a reduced-order model.

show abstract

Combustor performance enhancement through direct shear layer excitation

Cited by 163 publications

References 23 publications

Shear flow-driven combustion instability: Evidence, simulation, and modeling

Shear flow-driven combustion instability: Evidence, simulation, and modeling

Mitigation of thermoacoustic instability utilizing steady air injection near the flame anchoring zone

Reduced order modeling of reacting shear flow

Contact Info

Product

Resources

About