Control of grid‐connected
            <scp>PMSG</scp>
            ‐based wind turbine system with back‐to‐back converters topology using a new
            <scp>PIL</scp>
            integration method

Fekkak, Bouazza; Menaa, Mohamed; Loukriz, Abdelhamid; Kouzou, Abdellah

doi:10.1002/2050-7038.12882

Cited by 9 publications

(3 citation statements)

References 34 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…This increases the reliability of the designed software. In this research, this technique involves two main validation steps: model-in-theloop (MIL) and processor-in-the-loop (PIL) [45]- [47].…”

Section: Validating In Model Based Designmentioning

confidence: 99%

Design and PIL Test of High Performance MPPT Controller Based on P&O-Backstepping Applied to DC-DC Converter

Diouri¹,

Gaga

Senhaji³

et al. 2022

Journal of Robotics and Control

View full text Add to dashboard Cite

This paper presents the design, test and validation process of the maximum power point tracking (MPPT) based on the Perturb and Observe backstepping controller. The design of this robust controller follows a sequence of two tests of the validated model-based design (MBD) approach. Our contribution is to give a roadmap for designing, testing and validating embedded software for MPPT algorithms. Perturb and observe algorithm is used to generate the reference voltage which is used by the backstepping controller to generate the maximum power. Then, after simulation of all these techniques, generated optimized C code for the STM32F4 microcontroller is necessary to test the controller on embedded platform. Therefore, the algorithm of MPPT is simulated by Model in the Loop (MIL) and Processor in the Loop (PIL) techniques. The results show that the proposed system has full control over reference power, for different atmospheric changes, by backstepping and integrating into a 32-bit ARM microcontroller. In all of the various tests, the embedded software developed demonstrates high compliance and high performance with MPPT requirements.

show abstract

Section: Validating In Model Based Designmentioning

confidence: 99%

Design and PIL Test of High Performance MPPT Controller Based on P&O-Backstepping Applied to DC-DC Converter

Diouri¹,

Gaga

Senhaji³

et al. 2022

Journal of Robotics and Control

View full text Add to dashboard Cite

show abstract

“…The control scheme for a PMSG‐based WT is depicted in Figure 5. The direct and quadrant components of the stator current in the synchronous frame are used for independent control of the active and reactive power 30 . As shown, using Equation (5) and for a given wind speed, the optimum rotor speed is first calculated and compared with the measured rotor speed.…”

Section: Control Systemmentioning

confidence: 99%

A new reactive power compensation concept for distribution systems using a grid‐integrated hybrid photovoltaic/wind turbine system: PV‐WT‐STATCOM

Akbari

Taheri

et al. 2022

Circuit Theory & Apps

View full text Add to dashboard Cite

In this paper, a new concept based on an integrated hybrid energy system including photovoltaic (PV) and wind turbine (WT) for reactive power support of the grid is presented. Considering the shared grid-side converter in hybrid energy systems, which is preferably responsible for delivering active power to the grid, the remaining capacity of the converter after providing active power management is utilized as a static synchronous compensator (STATCOM) to overcome the power quality problems in the main grid. For this aim, a new concept named PV-WT-STATCOM is proposed, and a flexible control scheme is accordingly designed, which enables a sufficient reactive power compensation in both steady and transient states. The steady-state issues in the main grid are resolved using the remaining capacity of the shared inverter. In the transient mode, where a large amount of reactive power is probably needed for restoring the grid-side voltage while the unoccupied capacity of the shared inverter is not sufficient, a new control strategy is developed for reducing the PV's generated power, and providing more unused capacity in the shared inverter. The effectiveness of the proposed configuration in handling reactive power compensation in both steady and transient states are carried out using MATLAB/Simulink. The extensive simulation results in presence of the variable weather conditions confirm that the proposed concept is properly able to improve grid-side power factor and voltage in steady and transient modes, respectively, without requiring any additional STATCOM.

show abstract

“…An angle is formed between the a-axis and the q-axis, which, since the qd system is rotating, will be as a function of time. The electrical model of the permanent magnet synchronous generator in the synchronously rotating reference frame is given in equations ( 5) and ( 6) [37]:…”

Section: Pmsg Mathematical Modelmentioning

confidence: 99%

Multiple Linear Regression Approach for Sensorless MPPT of PMSG Wind Power Generation Systems

Abo‐Khalil

Sobhy

Sayed

2022

Preprint

View full text Add to dashboard Cite

In this paper, a novel approach for extracting the maximum power from a wind energy conversion system (WECS) eqquiped with a permanent magnet synchronous generator (PMSG) is presented. Wind power generation systems have gained prominence as an alternative to conventional power plants worldwide, being the renewable energy source with the best growth prospects. However, the intermittent nature of wind power reduces energy reliability and hinders the development of technologies in this area. Therefore, a sensorless controller for a WECS with a PMSG is developed to enhance the conversion efficiency of the wind enegy system. The proposed control algorithm predicts the wind speed from the wind turbine power-speed characteristics. It uses the predicted speed to determine the optimum reference rotating speed to extract the maximum power point (MPPT) based on the optimum tip-speed ratio. The proposed control approach is based on a multiple linear regression (MLR) algorithms which is used to predict the wind speed value by calculating the regression coefficients from the predetermined training samples of the turbine power, rotating speed, and wind speed. The MPPT operating mode is maintained as long as the available power is less than the rated power of the converter. Otherwise, the MPPT algorithm is disabled, and a mechanical power control loop guarantees nominal power. A complete theoretical analysis and the experimental results considering the prototype with the nominal power of the 3 kW wind turbine used are presented. The experimental results has proven the effectiveness and robustness of the proposed control approach.

show abstract

Control of grid‐connected PMSG ‐based wind turbine system with back‐to‐back converters topology using a new PIL integration method

Cited by 9 publications

References 34 publications

Design and PIL Test of High Performance MPPT Controller Based on P&O-Backstepping Applied to DC-DC Converter

Design and PIL Test of High Performance MPPT Controller Based on P&O-Backstepping Applied to DC-DC Converter

A new reactive power compensation concept for distribution systems using a grid‐integrated hybrid photovoltaic/wind turbine system: PV‐WT‐STATCOM

Multiple Linear Regression Approach for Sensorless MPPT of PMSG Wind Power Generation Systems

Contact Info

Product

Resources

About