Design and development of a DC-DC boost converter with constant output voltage

Masri, Syafrudin; Chan, P. W.

doi:10.1109/icias.2010.5716257

Cited by 33 publications

(12 citation statements)

References 2 publications

Supporting

Mentioning

Contrasting

Unclassified

Order By: Relevance

“…Driver LED terdiri dari converter. Boost converter merupakan topology dc-dc converter yang memiliki karakteristik menaikkan tegangan dengan cara mengatur duty cycle [5], [6]…”

Section: Pendahuluanunclassified

Hybrid Battery-Less Led Driver Menggunakan Boost Converter Berbasis Kontrol Proposional

Syafiuddin

2019

View full text Add to dashboard Cite

The Government policy about energy management based on regulations of the Minister of Energy and Mineral Resources number 13 and 14 on 2012 concern saving of electricity use and energy management as a form of utilizing energy resources effectively, efficiently, and rationally, without reducing building functions should be an energy audit. So LED Driver is made in this prototype to utilize energy from photovoltaic without batteries for building lighting in the daytime, so besides saving in terms of load (LED) it is also saving energy sources. This paper will discuss LED drivers using photovoltaic (PV). The use of hybrid battery-less led drivers in this paper to increase the rate of savings electricity usage in buildings. Led drivers have the hybrid designed that can replace the PV power supply to the PLN power supply when the power generated by PV is less than nominal power. The output voltage of the LED is controlled by STM32F1 microcontroller using a boost converter. Experimental results in the field voltage generated by the LED driver is 195 Vdc. The power produced by the LED driver is 100 watts using 4 LED. And the value of the efficiency of the Boost converter reaches 92%.

show abstract

“…Driver LED terdiri dari converter. Boost converter merupakan topology dc-dc converter yang memiliki karakteristik menaikkan tegangan dengan cara mengatur duty cycle [5], [6]…”

Section: Pendahuluanunclassified

Hybrid Battery-Less Led Driver Menggunakan Boost Converter Berbasis Kontrol Proposional

Syafiuddin

2019

View full text Add to dashboard Cite

show abstract

“…This converter is used to charge the battery at constant output current and also to maintain the output voltage at desired value in the constant current mode of operation and constant voltage after SOC is reached 80% to prevent the battery from over charging. Although controller discussed in [13][14][15][16][17] are helpful for controlling boost converter for voltage control and constant current with negative feedback control. In this system, the output current is sensed and compared with the reference current and the error signal e (t) is feed to PI controller.…”

Section: Control Technique For Constant Current Chargingmentioning

confidence: 99%

Design of DC-DC Boost Converter with Negative Feedback Control for Constant Current Operation

Rao¹,

Gairola²,

Lavety³

et al. 2017

IJPEDS

View full text Add to dashboard Cite

In this paper design of DC-DC boost converter with constant current control, charging is presented to charge the battery of electric vehicles. The different methods of battery charging are discussed. The charging profile of different types of batteries is investigated and compared with respect to charging time. The battery current is sensed and compared with a reference current and the generated actuating signal which is an error is feed to PI controller to compute a duty cycle of boost converter for constant current operation. A 6 V dc supply is obtained by using a step down transformer and diode rectifier. Boost converter parameters are designed for continuos conduction mode operation. The limiting values of duty cycle are fixed in the range of 0.5 to 0.6 for constant current operation. Simulation is carried out using MATLAB software for constant current operation connected to a 50 Ah, 12 V battery load. The constant current operation is achieved using negative feedback control. The switching frequency of boost converter is set to 20 kHz. The filter components are also designed to reduce ripple content within limited values. The simulation result shows the effectiveness of charging control for hardware implementation.

show abstract

“…The structure is showed up underneath in Fig. A, of transporter in blue, the reference in color red, and the yield in color green [10]. …”

Section: Invertermentioning

confidence: 99%

Analysis and Simulation of PV based Inverter System

Mamatha¹,

K.V²,

P³

2017

IJET

View full text Add to dashboard Cite

show abstract

Design and development of a DC-DC boost converter with constant output voltage

Cited by 33 publications

References 2 publications

Hybrid Battery-Less Led Driver Menggunakan Boost Converter Berbasis Kontrol Proposional

Hybrid Battery-Less Led Driver Menggunakan Boost Converter Berbasis Kontrol Proposional

Design of DC-DC Boost Converter with Negative Feedback Control for Constant Current Operation

Analysis and Simulation of PV based Inverter System

Contact Info

Product

Resources

About